ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.137 SNIP: 0.341 CiteScore™: 0.43

ISSN 印刷: 1093-3611
ISSN オンライン: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v14.i4.80
pages 379-388

PLASMA SPRAYING OF BORON CARBIDE USING TERNARY GAS MIXTURES

S. Janisson
CEA/DAM Le Ripault, BP 16 - 37260 Monts - France
Armelle Vardelle
ENSIL, ESTER Technopole, 87068 Limoges - France
Michel Vardelle
LMCTS-URA 320, University of Limoges, 123 Avenue Albert Thomas -87060 Limoges Cedex - France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France
Erick Meillot
CEA/DAM Le Ripault, BP 16 - 37260 Monts - France

要約

Materials which exhibit high specific heat and melting enthalpy combined with a low density, like boron carbide B4C, are difficult to melt by plasma spraying under standard spray conditions. Moreover, the injection of this low-density powder in the plasma jet is critical, especially when fine particles are used. The optimization of the plasma-forming gas composition may make the penetration of the particles in the gas flow easier, and improve their melting state. This paper presents an investigation of the effect of the composition of ternary gas mixtures of argon, helium and hydrogen on B4C particles heating and acceleration. The particle injection and the resulting spray pattern in the jet were controlled by using a 1D imaging technique. The particle velocity distribution was measured with a laser Doppler anemometer and the particle overall temperature with a high-speed pyrometer.

参考

  1. Janisson, S., Meillot, E., Vardelle, A., Coudert, J. F., Pateyron, B., and Fauchais, P. , Plasma Spraying Using Ar-He-H2 Ternary Gas Mixtures.

  2. Swank, W. D., Fincke, J. R., and Haggard, D. C. , A Particle Temperature Sensor for Monitoring and Control of the Thermal Spray Process.

  3. Pateyron, B. and Delluc, G. , ADEP - Databank of University of Limoges and CNRS.


Articles with similar content:

PLASMA SPRAYING OF BORON CARBIDE USING TERNARY GAS MIXTURES
Progress in Plasma Processing of Materials, 1999, Vol.1, 1999, issue
Michel Vardelle, Erick Meillot, S. Janisson, Pierre Fauchais, Armelle Vardelle
EXPERIMENTAL INVESTIGATION OF METAL PARTICLE VAPORIZATION IN PLASMA SPRAYING
Progress in Plasma Processing of Materials, 1997, Vol.1, 1997, issue
Michel Vardelle, C. Trassy, K.-I. Li, Pierre Fauchais
NUMERICAL ANALYSIS OF MOMENTUM, HEAT AND MASS TRANSFER BETWEEN A NITROGEN PLASMA JET AND B2O3 PARTICLES INJECTED IN AN AXISYMMETRIC REACTOR
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.14, 2010, issue 4
Zivota G. Kostic, Pavle B. Pavlovic, Dejan B. Cvetinovic, Predrag Lj. Stefanovic
THERMODYNAMIC CONSIDERATION OF THERMAL PLASMA PROCESS FOR ZIRCONIUM CARBIDE PRODUCTION FROM ZIRCON CONCENTRATES
Progress in Plasma Processing of Materials, 2001, Vol.0, 2001, issue
Zivota G. Kostic, Zoran N. Pavlovic, Pavle B. Pavlovic, Predrag Lj. Stefanovic, Nikola V. Zivkovic
A FLEXIBLE LOW PRESSURE PLASMA PROCESS FOR THE DEPOSITION OF COMPLEX THICK OXIDE COATINGS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.13, 2009, issue 3-4
F. Rousseau, S. Awamat, Daniel Morvan