ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.262 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v19.i8.10
pages 701-726

FORMATION AND DEVELOPMENT OF WALL LIQUID FILMS DURING IMPACTION OF GASOLINE FUEL SPRAYS

Maria Spathopoulou
City University London
Manolis Gavaises
School of Mathematics, Computer Science, and Engineering, City University London, Northampton Square, EC1V 0HB London, United Kingdom
Andreas P. Theodorakakos
Fluid Research Co, 49 Laskareos Str, 114 72, Athens
Hiromichi Yanagihara
Toyota Motor Europe, Brussels

要約

Laser-induced fluorescence (LIF) measurements and model predictions of the liquid film thickness formed on a flat surface during impingement of fuel sprays formed from low-pressure gasoline injectors are reported. The obtained measurements guide the development of a mathematical model employed to numerically predict the formation and transport of the wall liquid film. The governing film flow equations are based on the continuous Eulerian approach and are formulated according to the thin-film boundary layer framework. Extended parametric studies investigate the sensitivity of the model to different type and order of spatial and temporal discretization schemes. Governing parameters for the spray representation and wall impingement process are addressed, and their influence upon the behavior of the fuel film development is investigated. Droplet impact pressure is identified as the main driving force of the film transport process, as revealed through an order-of-magnitude analysis on the terms considered in momentum conservation equations. Model parameters defining the characteristics of the incident fuel droplets are additionally proved influential. Predictions under different injection conditions are compared against the temporal evolution of liquid film thickness at various locations over the impact wall. The numerical results capture the wavy variation of film thickness during the fuel film formation and transport along the solid surface from the time of impingement until equilibrium conditions have been reached. The latter is achieved at the final stages of mass exchange with the impinging jet, and it is well reproduced, although a tendency to under predict the peak thickness values during the initial and more transient stages of the formation process is revealed.

参考


Articles with similar content:

INVESTIGATION OF THE CHARACTERISTICS OF FUEL ADHESION FORMED BY SPRAY/WALL INTERACTION UNDER DIESEL PREMIXED CHARGE COMPRESSION IGNITION (PCCI) RELEVANT CONDITIONS
Atomization and Sprays, Vol.25, 2015, issue 11
Maozhao Xie, Hong Liu, Ming Jia, Yanzhi Zhang, Tianyou Wang
Dynamics of entrapped air bubble during impact of high-velocity molten droplet on a solid substrate
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Arvind Kumar, Digvijay Singh, Rajesh Kumar Shukla
NUMERICAL PREDICTIONS OF TRANSIENT COOLING AND PHASE CHANGE OF A FALLING WATER DROPLET IN SUB-ZERO AIR TEMPERATURES
Second Thermal and Fluids Engineering Conference, Vol.50, 2017, issue
Yuri S. Muzychka, Kevin Pope, Kaniz Ronak Sultana
CFD Study of Needle Motion Influence on the Spray Conditions of Single-Hole Injectors
Atomization and Sprays, Vol.21, 2011, issue 1
P. Fajardo, Xandra Margot, S. Patouna, Sergio Hoyas
Numerical study on nucleate pool boiling in a container using volume of fluid multiphase model
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
M. Prakash Maiya, Shaligram Tiwari, C. R. Aniraj