ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.262 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2018025001
pages 65-89

FROM HIGH-FIDELITY NUMERICAL SIMULATIONS OF A LIQUID-FILM ATOMIZATION TO A REGIME CLASSIFICATION

Camille Bilger
Department of Engineering, University of Cambridge, Trumpington Street, Cambridge, CB2 1PZ, United Kingdom
R. Stewart Cant
Department of Engineering, University of Cambridge, Trumpington Street, CB2 1PZ, Cambridge, United Kingdom

要約

High-fidelity numerical simulations of spray formation were conducted with the aim of improving fundamental understanding of airblast liquid-film atomization. The gas/liquid interaction in the near-nozzle region is investigated for a multitude of operating conditions in order to extrapolate phenomenological and breakup predictions. To reach this goal, the robust conservative level-set (RCLS) method was used. For a fixed prefilmer geometry, we performed a parametric study on the impact of various liquid and gas velocities on the topological evolution of the liquid interface. The behavior and development of the liquid film is found to be influenced mainly by the relative inertia of the gas and the liquid, the liquid surface tension, and interfacial shear stresses. Preliminary regime maps predicting the prefilming liquid-sheet atomization behavior are constructed based on our numerical results. Three distinct types of "regime" are reported: accumulation, ligament-merging, and three-dimensional wave mode. In addition, these results also show the influence of vortex action and rim-driven dynamics on the breakup mechanism at the atomizer edge. An increase in liquid injection speed leads to the generation of smaller droplets; whereas, an increase in air velocity does not point to one simple conclusion.


Articles with similar content:

CHARACTERIZATION OF THE INITIAL SPRAY FROM LOW-WEBER-NUMBER JETS IN CROSSFLOW
Atomization and Sprays, Vol.21, 2011, issue 7
Andre W. Marshall, Yinghui Zheng
EXPERIMENTAL STUDY OF COAXIAL ATOMIZERS SCALING. PART I: DENSE CORE ZONE
Atomization and Sprays, Vol.17, 2007, issue 5
Francois Lacas, Bertrand Leroux, Olivier Delabroy
DROPLET FORMATION FROM A THIN HOLLOW LIQUID JET WITH A CORE AIR FLOW
Atomization and Sprays, Vol.15, 2005, issue 4
Sang Yong Lee, Chul Jin Choi
DROPLET FORMATION FROM A THIN HOLLOW LIQUID JET WITH A CORE AIR FLOW
Atomization and Sprays, Vol.15, 2005, issue 5
Sang Yong Lee, Chul Jin Choi
Spray Trajectories of Liquid Fuel Jets in Subsonic Crossflows
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
R. P. Fuller, P.-K. Wu, K. A. Kirkendall, A. S. Nejad, M. R. Gruber