ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.262 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015013216
pages 755-773

TIME-RESOLVED CHARACTERIZATION OF LOW-PRESSURE PULSED INJECTOR

Rohit Singh Pathania
Department of Mechanical Engineering, National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India
Satyanarayanan R. Chakravarthy
Department of Aerospace Engineering, National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India
Pramod S. Mehta
Department of Mechanical Engineering, National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India

要約

This study concerns visualization of pulsed sprays of a gasoline port fuel injector under ambient conditions. One-, two-, and four-hole configurations all with the same hole diameter are compared. The investigations on the two-hole configuration include adjacent and diagonal holes. The instantaneous penetration length, the jet breakup length, cone angle, and the droplet diameter distributions are evaluated along the spray axis at different injection pressures. As the spray penetration evolves, the liquid jet breaks up some time later, and reaches a nearly constant breakup length throughout the subsequent development of the spray. Unlike the single-hole spray, the two-hole spray exhibits a mild increase in the breakup length with increase in the injection pressure. The breakup length with the diagonal two-hole configuration is much shorter than with the adjacent one. The diagonal two-hole configuration exhibits a high cone angle relative to two-hole and four-hole cases. In all the cases, the mean droplet size decreases with injection pressure and remains nearly constant in time at any axial location. While the single-hole and adjacent two-hole injectors indicate coalescence of droplets, the diagonal two-hole case shows a decrease in the Sauter mean diameter of the droplets with axial distance. The four-hole injector produces nearly constant droplet size. The shorter breakup length, higher spread, and smaller droplet sizes in the two-hole diagonal configuration support an enhanced entrainment of ambient air as compared to the two-hole adjacent and four-hole injector configurations.


Articles with similar content:

INTERNAL AND NEAR-NOZZLE FLOW OF A PRESSURE-SWIRL ATOMIZER UNDER VARIED FUEL TEMPERATURE
Atomization and Sprays, Vol.17, 2007, issue 6
Jaejoon Choi, Essam Abo-Serie, Choongsik Bae, Seoksu Moon
TRANSIENT 3D ANALYSIS OF A Dl GASOLINE INJECTOR SPRAY
Atomization and Sprays, Vol.9, 1999, issue 5
R. J. R. Johns, Colin J. Bates, Phil J. Bowen, M. A. Comer, S. M. Sapsford
MACROSCOPIC CHARACTERIZATION OF FLASH-BOILING MULTIHOLE SPRAYS USING PLANAR LASER-INDUCED EXCIPLEX FLUORESCENCE. PART II: CROSS-SECTIONAL SPRAY STRUCTURE
Atomization and Sprays, Vol.23, 2013, issue 3
David J. Cleary, Ming Zhang, Yuyin Zhang, Min Xu, Gaomimg Zhang
DEVELOPMENT OF MICRO-DIESEL INJECTOR NOZZLES VIA MEMS TECHNOLOGY AND EFFECTS ON SPRAY CHARACTERISTICS
Atomization and Sprays, Vol.13, 2003, issue 5&6
Michael L. Corradini, James P. Blanchard, Seunghyun Baik
IMPINGEMENT OF HIGH-PRESSURE GASOLINE SPRAYS ON ANGLED SURFACES
Atomization and Sprays, Vol.16, 2006, issue 6
Jim H. Whitelaw, J. M. Nouri