ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.262 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015011058
pages 375-396

MORPHOLOGICAL EXPLORATION OF EMERGING JET FLOWS FROM MULTI-HOLE DIESEL INJECTORS AT DIFFERENT NEEDLE LIFTS

Seoksu Moon
Department of Mechanical Engineering, Inha University
Xusheng Zhang
Advanced Photon Source, Argonne National Laboratory, Argonne, USA; Merchant Marine College, Shanghai Maritime University, Shanghai, China
Jian Gao
Advanced Photon Source, Argonne National Laboratory, Argonne, USA; Propulsion Systems Research Lab., General Motors Global Research and Development, Warren, USA
Kamel Fezzaa
Advanced Photon Source, Argonne National Laboratory, Argonne, USA
Eric M. Dufresne
Advanced Photon Source, Argonne National Laboratory, Argonne, USA
Jin Wang
Advanced Photon Source, Argonne National Laboratory, Argonne, IL, USA
Xingbin Xie
Department of Mechanical Engineering, Wayne State University, Detroit, USA
Fengkun Wang
Department of Mechanical Engineering, Wayne State University, Detroit, USA
Ming Chia Lai
Department of Mechanical Engineering, Wayne State University, Detroit, MI 48202

要約

The current study takes a morphological approach to interpret the emerging jet flows from multi-hole diesel injectors. Several types of multi-hole injectors, a six-hole injector and two two-hole injectors with different needle control mechanisms, were used to investigate the emerging jet flows and related flow breakup at different needle lifts. A short X-ray pulse with 150 ps duration was used to visualize the nearfield morphologies of the emerging jet flows using an ultrafast X-ray phase-contrast imaging technique. A few X-ray pulses with 68 ns periodicity were also used to analyze the dynamics of the emerging jet flows by tracking the movement of the structures inside the spray. At first, the effects of needle lift on emerging flow pattern and breakup were investigated using a six-hole injector under practical injection conditions. A highly expanding spray was observed at the low needle lifts. The degree of flow expansion was however suppressed with an increase in the needle lift. The higher degree of flow expansion at the low needle lifts promoted the flow breakup and increased the spray deceleration rate with an increase in the axial distance. Then, a detailed morphological study of the emerging flows was performed using two-hole nozzles under low injection pressures to slow down the flow breakup in order to figure out the intrinsic nature of the emerging flows associated with the nozzle internal flow. The phase-contrast images revealed clear morphologies of several branching flows inside the spray having different flowing directions and stretching the spray three-dimensionally that originate from complex nozzle internal flow pattern. The degree of flow expansion associated with the branching flows appeared differently with the needle lift with formation of various flow structures: cone shaped, stretched thin, and cylindrical. At certain needle lifts, the branching flows sometimes formed a couple of microwavelets inside the spray having different instability frequencies, indicating different origins of each flow associated with nozzle internal flow. Increasing ambient gas density did not alter the branching characteristics of the flows significantly, while increasing injection pressure and reducing the fuel viscosity significantly altered the branching flow characteristics.


Articles with similar content:

INFLUENCE OF VORTEX FLOW AND CAVITATION ON NEAR-NOZZLE DIESEL SPRAY DISPERSION ANGLE
Atomization and Sprays, Vol.19, 2009, issue 3
Manolis Gavaises, A. Andriotis
NUMERICAL ANALYSIS OF THE INFLUENCE OF DIESEL NOZZLE DESIGN ON INTERNAL FLOW CHARACTERISTICS FOR 2-VALVE DIESEL ENGINE APPLICATION
Atomization and Sprays, Vol.23, 2013, issue 2
Joaquin De la Morena, Kshitij Neroorkar, Alejandro H. Plazas, David P. Schmidt, Richard C. Peterson
EFFECT OF NOZZLE CONFIGURATION ON MACROSCOPIC SPRAY CHARACTERISTICS OF MULTI-HOLE FUEL INJECTORS UNDER SUPERHEATED CONDITIONS
Atomization and Sprays, Vol.26, 2016, issue 5
Gele Aori, Ming Zhang, David L. S. Hung, Tianyun Li, Gaomimg Zhang
INTERNAL FLOW PATTERN AND MACROSCOPIC CHARACTERISTICS OF A FLASH-BOILING SPRAY ACTUATED THROUGH A TWIN-ORIFICE ATOMIZER WITH LOW INJECTION PRESSURE
Atomization and Sprays, Vol.26, 2016, issue 4
Zhen Huang, Xinqi Qiao, Jin Xiao , Chunhai Wang, Dehao Ju
ATOMIZATION CHARACTERISTICS OF PRESSURE-MODULATED AUTOMOTIVE PORT INJECTOR SPRAYS
Atomization and Sprays, Vol.6, 1996, issue 4
Fu-Quan Zhao, Amer Ahmad Amer, John L. Dressler