ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.262 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2017019656
pages 707-722

QUANTIFYING THE EFFECTS OF FUEL COMPOSITIONS AND PROCESS VARIABLES ON PLANAR SURFACE AREA AND SPRAY NONUNIFORMITY VIA COMBINED MIXTURE-PROCESS DESIGN OF EXPERIMENT

Longfei Chen
School of Energy and Power Engineering, Energy and Environment International Center, Beihang University, 100091, China
Liuyang Feng
School of Energy and Power Engineering, Energy and Environment International Center, Beihang University, 100091, China
Zhixin Liu
School of Energy and Power Engineering, Beihang University, Beijing, China
Guangze Li
School of Energy and Power Engineering, Beihang University, Beijing, China
Yanfei Li
State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing, 100084, China
Yiji Lu
Sir Joseph Swan Centre for Energy Research, Newcastle University, Newcastle, NE1 7RU, United Kingdom
Anthony Paul Roskilly
Sir Joseph Swan Centre for Energy Research, Newcastle University, Newcastle, NE1 7RU, United Kingdom

要約

The planar surface area and the spray nonuniformity are important parameters for determining spray evaporation characteristics. In this study, the effects of fuel compositions and two process variables (the injection pressure and axial distance from the measurement plane to the nozzle exit) on both planar surface area and spray nonuniformity were experimentally investigated via statistical extinction tomography. The design of experiment (DoE) was adopted to design the experiment procedure and analyze the data in a systematic way by establishing quadratic mixture models crossed with a linear process model. The planar surface area and the spray nonuniformity were calculated from spatial distributions of surface area density at three measurement planes, which were obtained by using an optical patternator SETSCAN OP-200. The results demonstrated that the axial distance had a significant influence on the planar surface area; whereas, the injection pressure did not show a definite trend for all the test fuels, yet the interaction between the injection pressure and fuel compositions played a noticeable role in determining the planar surface area. The spray nonuniformity was primarily influenced by injection pressure, while it exhibited little dependence on the axial distance. In general, the higher the injection pressure, the higher the spray nonuniformity would be. Fuel composition had an appreciable effect on the spray nonuniformity as well. The DoE-derived models were statistically significant according to analysis of variance analysis, and the optimal values in terms of planar surface area and spray nonuniformity were determined via numerical optimization.