ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.737 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 30, 2020 巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2014010997
pages 1017-1033

A NUMERICAL METHOD FOR ANALYSIS OF SPRAY BEHAVIOR WITH DESIGN OF EXPERIMENT

Jeongkuk Yeom
Department of Mechanical Engineering, Dong-A Univ., 37 Nakdong-Daero 550 beon-gil saha-gu, Busan 604-714, Korea
Hyungsoo Ha
Graduate School, Department of Mechanical Engineering, Dong-A Univ., 37 Nakdong-Daero 550 beon-gil saha-gu, Busan 604-714, Korea

要約

The purpose of the present study is to optimize the diesel engine injector. Discharge of many cavitation bubbles and high injection velocity were set up for the design purpose. Injector optimization was progressed through computational fluid dynamics (CFD) and the design of the experiment was used to study the interior of the injector. ANSYS CFX 13.0 was used as the CFD tool to perform the CFD analysis of 16 experimental cases; these include four cases of each design variable; the hole diameter, the hole length, the hole angle, and the K factor. The results of the analysis show that the largest impact on the cavitation comes from the K factor, and the injection velocity dominantly depends on the hole diameter. The optimum injector derived based on these results has the size of 2, 4, 4, and 4 levels, respectively, for the hole diameter, the hole length, the hole angle, and the K factor. For the injection velocity of 460 m/s, it gives the best performance when 36% volume fraction of cavitation bubbles are injected.


Articles with similar content:

OPTIMIZATION OF THE OVERALL PERFORMANCE OF CYCLONE SEPARATORS
Energy and the Environment, 1998, Vol.0, 1998, issue
M.I. Bakari , Feridun Hamdullahpur
THERMAL ANALYSIS OF RECTANGULAR FINS WITH DIFFERENT SHAPES OF LATERAL PERFORATIONS BY FORCED CONVECTION
Heat Transfer Research, Vol.49, 2018, issue 7
Kavita H. Dhanawade, Vivek K. Sunnapwar, Hanamant S. Dhanawade
Performance Evaluation of Divided Intake Ducts: Effect of Area Ratio and Inlet Reynolds Number
International Journal of Fluid Mechanics Research, Vol.30, 2003, issue 5
Sidh Singh, R. Chandramouli, V. Seshadri, Sanjeev Bharani
A COMPARATIVE STUDY OF THE FILM COOLING HOLE CONFIGURATION EFFECTS ON THE LEADING EDGE OF ASYMMETRICAL TURBINE BLADE
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2009, issue
Abbes Azzi, B. A. Jubran, Mustapha Benabed
EXPERIMENTAL STUDY OF CONICAL DIESEL NOZZLE ORIFICE GEOMETRY
Atomization and Sprays, Vol.25, 2015, issue 6
Martti Larmi, Ossi Kaario, Tuomo Hulkkonen, Teemu Sarjovaara, Ismo Hamalainen