Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Heat Transfer Research
Fator do impacto: 1.199 FI de cinco anos: 1.155 SJR: 0.267 SNIP: 0.503 CiteScore™: 1.4

ISSN Imprimir: 1064-2285
ISSN On-line: 2162-6561

Volumes:
Volume 51, 2020 Volume 50, 2019 Volume 49, 2018 Volume 48, 2017 Volume 47, 2016 Volume 46, 2015 Volume 45, 2014 Volume 44, 2013 Volume 43, 2012 Volume 42, 2011 Volume 41, 2010 Volume 40, 2009 Volume 39, 2008 Volume 38, 2007 Volume 37, 2006 Volume 36, 2005 Volume 35, 2004 Volume 34, 2003 Volume 33, 2002 Volume 32, 2001 Volume 31, 2000 Volume 30, 1999 Volume 29, 1998 Volume 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2016013742
pages 625-656

MODELING OF FLUID FLOW AND HEAT TRANSFER OF AA1050 ALUMINUM ALLOY IN A MODERN LOW-HEAD DIRECT-CHILL SLAB CASTER

Latifa Begum
Department of Mining and Materials Engineering, McGill University, M.H. Wong Building, 3610 University Street,Montreal, QC, H3A 0C5, Canada
Mainul Hasan
Department of Mining and Materials Engineering, McGill University, M.H. Wong Building, 3610 University Street,Montreal, QC, H3A 0C5, Canada

RESUMO

A low-head hot-top mold is modeled for the vertical direct-chill casting (DCC) process where the melt is assumed to have been delivered through the entire top cross section of the caster. The previously verified in-house 3D Computational Fluid Dynamics (CFD) code is extended to model an industrial-sized AA1050 slab for the above caster for steady-state operation. For the generalization of the predicted results, nondimensional parameters governing this problem were identified. To keep consistency with the industrial cooling strategy, a stepwise change of the cooling water temperature in the mold, in the impingement and in free streaming regions was considered. A series of parametric studies were conducted by varying the important DCC process parameters, namely the casting speed ranging from 60 to 180 mm/min, inlet melt superheat, ranging from 16°C to 64°C, as well as the effective heat transfer coefficient (HTC) at the metal–mold contact region, varying from 0.75 to 3.0 kW/(m2·K). The velocity field, the temperature distributions, and the local surface temperature profiles are presented and discussed. The sump depth and the mushy thickness at the ingot center are seen to increase linearly with the increasing casting speed, whereas the shell thickness at the exit of the mold decreases linearly with the casting speed. The thickness of the solid shell at the mold exit is increased by about 4% for the aforementioned increase in HTC. Correlations of the above-mentioned quantities with casting speed are reported to provide useful guidelines for vertical DCC design engineers and operators.


Articles with similar content:

NUMERICAL ASSESSMENT OF INTERFACIAL HEAT TRANSFER COEFFICIENT IN A MG SQUEEZE CASTING WITH VARIOUS SECTION THICKNESS BY POLYNOMINAL EXTRAPOLATION
International Heat Transfer Conference 16, Vol.6, 2018, issue
Henry Hu, Zhizhong Sun, Luyang Ren
INVESTIGATION OF SHRINKAGE RELATED LEAKAGE IN CI SAND CASTING − STUDY AND CONTROL USING SIMULATION AND EXPERIMENTAL VALIDATION
Nanoscience and Technology: An International Journal, Vol.11, 2020, issue 2
Neeraj Sharma, Sarabjit Singh, Rajesh Khanna
Experimental and Numerical Investigation of Thermal-Hydraulic Characteristics of a Wavy-Channel Compact Heat Exchanger
International Heat Transfer Conference 12, Vol.52, 2002, issue
Raj M. Manglik, Arun Muley, Joseph B. Borghese, Jaydeep Kundu
AN EXPERIMENTAL INVESTIGATION OF REWETTING OF HOT HORIZONTAL SURFACE BY BOTTOM JET IMPINGEMENT
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Shubham K. Mishra, Avadhesh Kumar Sharma, Mayank Modak, Santosh K. Sahu
Boiling Heat Transfer From Oscillating Surface
Journal of Enhanced Heat Transfer, Vol.1, 1994, issue 2
Zitko Vinko, Afgan Naim