Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
International Journal for Uncertainty Quantification
Fator do impacto: 3.259 FI de cinco anos: 2.547 SJR: 0.417 SNIP: 0.8 CiteScore™: 1.52

ISSN Imprimir: 2152-5080
ISSN On-line: 2152-5099

Open Access

International Journal for Uncertainty Quantification

DOI: 10.1615/Int.J.UncertaintyQuantification.2013005786
pages 487-498

OPTIMAL DESIGN UNDER UNCERTAINTY OF REINFORCED CONCRETE STRUCTURES USING SYSTEM RELIABILITY APPROACH

Younes Aoues
INSA Rouen, Laboratoire d'Optimisation et Fiabilité en Mécanique des Structures (LOFIMS), France
Alaa Chateauneuf
Institut Pascal, Laboratoire de Mécanique et Ingenieries, Université Blaise Pascal, France
Didier Lemosse
INSA Rouen, Laboratoire d'Optimisation et Fiabilité en Mécanique des Structures (LOFIMS), France
Abdelkhalak El-Hami
INSA Rouen, Laboratoire d'Optimisation et Fiabilité en Mécanique des Structures (LOFIMS), France

RESUMO

The design of reinforced concrete (RC) structures involves several kinds of uncertainties, which are usually considered through the partial safety factors prescribed in the codes of practice. The traditional design optimization of RC structures uses deterministic information of the problem. The partial safety factors are used to consider loading fluctuation and the variability of material properties. The use of these safety factors in deterministic optimization usually leads to over-designing structures, as these safety factors are calibrated for a large class of structures. In the deterministic optimization procedure the reliability cannot be controlled. For this reason, the Reliability-Based Design Optimization (RBDO) is devoted to design economical and reliable structures. However, the RBDO problem involves the evaluation of probabilistic constraints performed by the reliability analysis. The most common RBDO formulations are based on a nested optimization problem, with an outer loop for the design optimization and an inner loop for the reliability analysis. Therefore, an expensive computation effort is required to solve the RBDO problem. In this paper, a new RBDO method of RC structures is proposed. The RBDO problem is decomposed to several cycles of deterministic design optimization (DDO) based on new safety factors called Optimal System Safety Factors (OSSF). At each cycle of the DDO, the system reliability analysis is performed to verify the reliability of the optimal design, the OSSF are computed by a probabilistic method on the basis of the previous system reliability analysis, then the updated OSSF are provided for the next cycle of the DDO. The application to the design of an RC structure shows the interest and the efficiency of the proposed method.

Referências

  1. EUROCODES-2, Design of Concrete Structures.

  2. Mohamed, A., Soares, R., and Venturini, W., Partial safety factors for homogeneous reliability of nonlinear reinforced concrete column. DOI: 10.1016/S0167-4730(01)00009-1

  3. Adeli, H., Advances in Design Optimization.

  4. Lee, C. and Ahn, J., Flexural design of reinforced concrete frames by genetic algorithm. DOI: 10.1061/(ASCE)0733-9445(2003)129:6(762)

  5. Moharrami, H. and Grierson, D., Computer-automated design of reinforced concrete frameworks. DOI: 10.1061/(ASCE)0733-9445(1993)119:7(2036)

  6. Ditlevsen, O. and Madsen, H., Structural Reliability Method.

  7. Frangopol, D. and Moses, F., Reliability-Based Structural Optimization.

  8. Moses, F., Problems and prospects of reliability-based optimization. DOI: 10.1016/S0141-0296(97)83356-1

  9. Hohenbichler, M. and Rackwitz, R., First-order concepts in system reliability. DOI: 10.1016/0167-4730(82)90024-8

  10. Feng, Y. and Moses, F., A method of structural optimization based on structural system reliability. DOI: 10.1080/03601218608907527

  11. Enevoldsen, I. and Sorensen, J., Reliability-based optimization in structural engineering. DOI: 10.1016/0167-4730(94)90039-6

  12. Lin, K. and Frangopol, D., Reliability-based optimum design of reinforced concrete girders. DOI: 10.1016/0167-4730(96)00013-6

  13. Aoues, Y. and Chateauneuf, A., Reliability-based optimization of structural systems by adaptive target safety - application to reinforced concrete frames. DOI: 10.1016/j.strusafe.2006.10.002

  14. Du, X. and Chen, W., Sequential optimization and reliability assessment method for efficient probabilistic design. DOI: 10.1115/1.1649968

  15. Sarma, K. and Adeli, H., Cost optimization of concrete structures. DOI: 10.1061/(ASCE)0733-9445(1998)124:5(570)

  16. Ditlevsen, O., Narrow reliability bounds for structural systems. DOI: 10.1080/03601217908905329

  17. Ambartzumian, R., Kiureghian, A. D., Ohaniana, V., and Sukiasiana, H., Multinormal probability by sequential conditioned importance sampling: theory and application. DOI: 10.1016/S0266-8920(98)00003-4

  18. Envoldsen, I. and Sorensen, J., Reliability based optimization of series systems of parallel systems. DOI: 10.1061/(ASCE)0733-9445(1993)119:4(1069)

  19. Tu, J. and Choi, K., A new study on reliability-based design optimization. DOI: 10.1115/1.2829499

  20. Schittkowski, K., Zillober, C., and Zotemantel, R., Numerical comparison of nonlinear programming algorithms for structural optimization. DOI: 10.1007/BF01742498


Articles with similar content:

Probabilistic Approach in Wind Induced Vibrations of Structures
International Journal of Fluid Mechanics Research, Vol.29, 2002, issue 3&4
P. Marek, O. Fischer, M. Pirner
RECONCILED TOP-DOWN AND BOTTOM-UP HIERARCHICAL MULTISCALE CALIBRATION OF BCC FE CRYSTAL PLASTICITY
International Journal for Multiscale Computational Engineering, Vol.15, 2017, issue 6
Aaron E. Tallman, David L. McDowell, Laura P. Swiler, Yan Wang
A CROSS-ENTROPY METHOD ACCELERATED DERIVATIVE-FREE RBDO ALGORITHM
International Journal for Uncertainty Quantification, Vol.6, 2016, issue 6
Tian Gao , Jinglai Li
SYSTEMS CFD ANALYSIS OF COMPLEX THERMAL-FLUID SYSTEMS
International Heat Transfer Conference 13, Vol.0, 2006, issue
Gideon P. Greyvenstein, Charl G. Jat Du Toit, Pieter G. Rousseau
SELECTION AND COMPARATIVE EVALUATION OF CONVENTIONAL AND RAPID PROTOTYPING PROCESS CHAINS OF THE TOOL AND DIE-MAKING INDUSTRY BASED ON AN INTEGRATED INFORMATION MODEL
Flexible Automation and Intelligent Manufacturing, 1997:
Proceedings of the Seventh International FAIM Conference, Vol.0, 1997, issue
Uwe Kaschka, Holger Durr