Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
ESCI SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Imprimir: 1093-3611
ISSN On-line: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v14.i4.40
pages 341-351

OXIDATION AND SPLATS OF STAINLESS STEEL PARTICLES COATED WITH AN ALUMINA SHELL

Helene Ageorges
University of Angers, LETP, 2 Boulevard Lavoisier, 49045 Angers Cedex, France
Pierre Fauchais
Laboratoire Sciences des Procedes Ceramiques et de Traitements de Surface UMR CNRS 6638 University of Limoges 123 avenue Albert Thomas, 87060 LIMOGES - France

RESUMO

The effect of an alumina shell (4 μm thick), obtained by mechanofusion, on stainless steel particles (d = 55 μm) used in plasma sprayed has been studied by examining the corresponding composite spraying particles collected in flight, their resulting splats and coatings. Without alumina, the collected sprayed stainless steel particles exhibit dark spots within their clear cross section, dark spots which display chromium and oxygen elements prominently which seems to be CrO (XRD). The composite sprayed particles are less oxidized. Parts of them keep their alumina shell broken but still covering the whole stainless steel particles. The EDS analysis of the distribution of the various elements in the corresponding splats shows that the alumina is dispersed in pieces and frozen over the surface of the stainless steel splat. The other parts have their alumina shell completely fused and entrained by the flow to the tail of the moving droplet. In this case, the alumina is spread exactly on the stainless steel splat. Whatever may be the type of particles, without preheating the substrate the splats are extensively fingered and become circular when the stainless steel substrate surface is preheated over 200°C. Finally, when comparing coatings on a rough (Ra ≈ 6.7 ± 0.3 μm) stainless steel substrate preheated to 400° C, both hardness and adhesion/cohesion are found to be improved for the alumina coated particles.


Articles with similar content:

OXIDATION AND SPLATS OF STAINLESS STEEL PARTICLES COATED WITH AN ALUMINA SHELL
Progress in Plasma Processing of Materials, 2001, Vol.0, 2001, issue
Helene Ageorges, Pierre Fauchais
OXIDATION OF STAINLESS STEEL PARTICLES WITH AND WITHOUT AN ALUMINA SHELL DURING THEIR FLIGHT IN A PLASMA JET
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.4, 2000, issue 3
Helene Ageorges, Pierre Fauchais
INFLUENCE OF SUBSTRATE SURFACE OXIDATION STAGE ON THE MORPHOLOGY AND FLATTENING OF SPLATS
Progress in Plasma Processing of Materials, 2003, Vol.0, 2003, issue
J. C. Labbe, A. A. Syed, Alain Denoirjean, Pierre Fauchais, P. Denoirjean
INFLUENCE OF SUBSTRATE SURFACE OXIDATION STAGE ON THE MORPHOLOGY AND FLATTENING OF SPLATS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.7, 2003, issue 2
J. C. Labbe, A. A. Syed, Alain Denoirjean, Pierre Fauchais, P. Denoirjean
PLASMA SPRAYED COATINGS OF MECHANOFUSED ALUMINA-STEEL PARTICLES
Progress in Plasma Processing of Materials, 1999, Vol.1, 1999, issue
Helene Ageorges, Alain Grimaud, Pierre Fauchais