Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
ESCI SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Imprimir: 1093-3611
ISSN On-line: 1940-4360

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v8.i4.110
pages 617-625

HIGH-TEMPERATURE ARC IN DENSE GAS

A. A. Bogomaz
Institute for Electrophysics and Electric Power Russian Academy of Sciences (IEE RAS),Dvortsovaya nab. 18, St.-Petersburg, 191186, Russia
A. V. Budin
Institute for Electrophysics and Electric Power Russian Academy of Sciences (IEE RAS),Dvortsovaya nab. 18, St.-Petersburg, 191186, Russia
M. E. Pinchuk
Institute for Electrophysics and Electric Power Russian Academy of Sciences (IEE RAS),Dvortsovaya nab. 18, St.-Petersburg, 191186, Russia
Philip G. Rutberg
Institute of Problems of Electrophysics of Russian Academy of Sciences 191186, Russia, St. Petersburg, Dvortsovaya nab. 18
A. F. Savvateev
Institute of Problems of Electrophysics of Russian Academy of Sciences (IPE RAS), Dvortsovaya nab. 18, St.-Petersburg, 191186, Russia

RESUMO

The investigations of the powerful electric discharge in high density hydrogen were continued in IPE RAS. In these experiments the influence of discharge current magnitude, current rise rate and initial particle density on arc temperature was investigated. These experiments were performed under the following conditions: charge voltage of the capacitive energy supply — 8.0−14.0 kV, stored energy — 140−450 kJ, discharge current — 200−600 kA, current rise rate — 109−1010 A/s. The maximum particle density nmax, achieved just before the discharge was about 2.0×1022 cm−3. Arc temperature was calculated on the basis of measured electric parameters of arc and bright temperature of its outer layer.
It was revealed that increasing in initial particle density, discharge current magnitude and current rise rate leads to the reducing of arc diameter that results in increasing of temperature of the discharge channel. Obtained experimental data permits to define the main parameters of the discharge: temperature of arc channel, plasma conductivity and density of charged particles in the arc channel. It was estimated that temperature of arc central zone is achieved 3×105 K at the specified initial conditions.


Articles with similar content:

HIGH-CURRENT ARC IN DENSE GAS
Progress in Plasma Processing of Materials, 2003, Vol.0, 2003, issue
A. F. Savvateev, A. V. Budin, Philip G. Rutberg, A. A. Bogomaz, V. A. Kolikov
EXPERIMENTAL STUDY OF A PULSE PLASMA FLOW IN A MODE OF DIAMOND-LIKE COATING DEPOSITION
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.10, 2006, issue 4
V. G. Tatur, A. I. Zolotovsky, E .I. Tochitsky, I. P. Smyaglikov
PULSE PLASMA GENERATORS, POSSIBLE APPLICATIONS
Progress in Plasma Processing of Materials, 1997, Vol.1, 1997, issue
Philip G. Rutberg, A. A. Bogomaz, V. A. Kolikov
QUANTITATIVE MEASUREMENT OF ATOMIC OXYGEN DENSITY IN A MICROWAVE GENERATED AIR PLASMA BY LASER INDUCED FLUORESCENCE
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.1, 1997, issue 1
P. Peze, J. Siffre, M. Balat, M. Lebrun
ELECTROARC DISCHARGE IN CONDITIONS BOW-CONTACT CUTTING OF METAL
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.5, 2001, issue 1
V. Frolov