Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Multiphase Science and Technology
SJR: 0.124 SNIP: 0.222 CiteScore™: 0.26

ISSN Imprimir: 0276-1459
ISSN On-line: 1943-6181

Multiphase Science and Technology

DOI: 10.1615/MultScienTechn.v19.i2.40
pages 167-181

JET IMPINGEMENT BOILING IN HOT SURFACES WELL ABOVE THE LIMITING TEMPERATURE FOR SOLID-LIQUID CONTACT

M. A. Islam
Dept. of Mechanical Engineering, Saga University, 1 Honjo Saga City, Saga 840-8502, Japan
Masanori Monde
Department of Mechanical Engineering, Saga University, 1 Honjo Saga City, Saga 840-8502, Japan
P. L. Woodfield
Dept. of Mechanical Engineering, Saga University, 1 Honjo Saga City, Saga 840-8502, Japan
Yuichi Mitsutake
Department of Mechanical Engineering, Saga University, 1 Honjo Saga City, Saga 840-8502, Japan
A. K. Mozumder
Dept. of Mechanical Engineering, Saga University, 1 Honjo Saga City, Saga 840-8502, Japan

RESUMO

Jet impingement boiling phenomena in hot surfaces were investigated by means of temperature measurements and video records. A 2-mm water jet of 5−80 K subcooling and of 3−15 m/s velocity was impinged on the flat surface of a cylindrical steel or brass block that was preheated to 400−600°C. During the quench, the transient temperature responses of 16 thermocouples embedded in two depths beneath the surface were recorded to estimate surface temperature by an inverse heat conduction technique. A high-speed video camera was also employed to capture images of boiling and flow phenomena. Sometimes the flow became explosive/noisy and sometimes very calm and quiet. Different flow patterns, as identified from video images, resulted from the interactions between the jet and vapor bubbles formed at/near the impinging surface. The flow patterns are found to be dependent on the block material and its surface temperature. It is also found that for a certain period of time, the surface temperature (Tω) remains well above the thermodynamic limiting temperature (Tmax) for solid-liquid contact. The cooling curves at the center of the impinging surface for different experimental conditions are explained in relation to the limiting temperature. A theoretical approach to elucidate the early-stage phenomena is also outlined in this study.


Articles with similar content:

BOILING AND WETTING PHENOMENA OF HOT SURFACE DURING JET IMPINGEMENT QUENCHING
International Heat Transfer Conference 13, Vol.0, 2006, issue
Yuichi Mitsutake, Masanori Monde, P. L. Woodfield, A. K. Mozumder
HEAT TRANSFER DURING TRANSIENT COOLING OF HIGH TEMPERATURE SURFACE WITH AN IMPINGING JET
Multiphase Science and Technology, Vol.12, 2000, issue 3&4
Yuichi Mitsutake, Masanori Monde
Visual Observation of Liquid-Solid Contact Situations on Superheated Surface Cooled by Liquid Jet or Spraying
International Heat Transfer Conference 15, Vol.15, 2014, issue
Niro Nagai, Hitoshi Nikaido, Yoshihiro Serizawa, Hiroki Onishi
Effect of Intial Temperature of a Hot Steel Plate on Thermal Performance of Impinging Jets During Quenching Processes
International Heat Transfer Conference 15, Vol.15, 2014, issue
Jang-Min Park, Dong-Wook Oh, Tae Hoon Kim, Jung Ho Lee, Kyu Hyung Do
Freezing of supercooled water droplets impinging upon solid surfaces
International Heat Transfer Conference 12, Vol.33, 2002, issue
Koji Matsushima, Yasuhiko H. Mori