Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.737 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 30, 2020 Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v12.i4.50
pages 431-449

CHARACTERISTICS OF INTERIMPINGEMENT DIESEL SPRAY

Takayuki Chiba
Department of Mechanical System Engineering, Gunma University, Kiryu, Gunma, Japan
Masahiro Saito
Department of Mechanical System Engineering, Gunma University, Kiryu, Gunma, Japan
Kenji Amagai
Department of Mechanical System Engineering, Gunma University, Kiryu, Gunma, Japan
Masataka Arai
Division of Mechanical Science and Technology, Faculty of Science and Technology, Gunma University, 1-5-1 Tenjin-cho, Kiryu, Gunma, 376-8515, Japan; Tokyo Denki University

RESUMO

A mutual impingement of spray in a diesel engine was tried to assess the probability of further atomization of conventional diesel spray. The effects of impingement distance and impingement angle on the characteristics of the impingement spray were investigated by comparing with a nonimpingement free spray. In this study, the experiment was conducted for two typical impingement patterns, the jet-to-jet impingement of liquid columns in the vicinity of the nozzles and the spray-to-spray impingement of fully developed sprays away from the nozzles. The spray tip penetration was reduced rapidly after the impingement in both cases of jet-to-jet and spray-to-spray impingements with impingement angle of 90°. On the other hand, in the case of spray-to-spray impingement with 60° impingement, the penetrations were longer than that of free spray at just after the impingement. Spray tip velocity was calculated by differentiating the spray tip penetration curve. In the case of 90' impingement, the spray tip velocity was reduced rapidly by the impingement. However, in the case of spray-to-spray impingement with 60' impingement, the impinged spray had a tendency to increase instantaneously just after the impingement. This means that the spray may be accelerated by the mutual impingement. Atomization behavior was observed using a high-speed camera and it was found that the mutual impingement of diesel sprays caused the swelling of the sprays after the impingement. So, a simple model for estimation of impinging spray volume was proposed. The spray volume was about 1.5 times larger than that of free spray when the impingement distance was near the breakup point of the free spray. Also, the Sauter mean diameter (SMD) of the impingement spray was compared with that of nonimpingement free spray. The result showed that the SMD was slightly smaller compared with that of the free spray in the case of spray-to-spray impingement.


Articles with similar content:

ATOMIZATION CHARACTERISTICS OF JET-TO-JET AND SPRAY-TO-SPRAY IMPINGEMENT SYSTEMS
Atomization and Sprays, Vol.9, 1999, issue 4
Masataka Arai, Masahiro Saito
THE CHARACTERISTICS OF POSTIMPINGEMENT DIESEL SPRAY, PART II: EMPIRICAL EQUATION OF PENETRATION
Atomization and Sprays, Vol.12, 2002, issue 4
Masataka Arai, Kyungnam Ko
SPRAY CHARACTERISTICS OF A GROUP-HOLE NOZZLE FOR DIRECT-INJECTION DIESEL ENGINES
Atomization and Sprays, Vol.16, 2006, issue 1
Shinsuke Nomura, Keiya Nishida, Tomoaki Ito, Yuyin Zhang
EXPERIMENTAL STUDY ON FLOW FIELDS OF FUEL DROPLETS AND AMBIENT GAS OF DIESEL SPRAY-FREE SPRAY AND FLAT-WALL IMPINGING SPRAY
Atomization and Sprays, Vol.24, 2014, issue 7
Takumi Uemura, Keiya Nishida, Jingyu Zhu
MODELING OF GROUP-HOLE-NOZZLE SPRAYS USING GRID-SIZE-, HOLE-LOCATION-, AND TIME-STEP-INDEPENDENT MODELS
Atomization and Sprays, Vol.19, 2009, issue 6
Rolf D. Reitz, Chang Sik Lee, Neerav Abani, Sung Wook Park, Hyun Kyu Suh