Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.737 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 30, 2020 Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v14.i3.10
20 pages

EXPERIMENTAL INVESTIGATION OF WATER MIST COOLING FOR GLASS TEMPERING

Nedim Sozbir
Mechanical Engineering Department, Carnegie Mellon University, Pittsburgh, Pennsylvania, USA
Shi-Chune Yao
Department of Mechanical Engineering, Institute for Complex Engineered Systems, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA, USA

RESUMO

High-velocity air jet impingement has been applied during the cooling process of glass tempering. In order to reduce the usage of high-pressure air in the process, it is intended to demonstrate the feasibility of using water mist to enhance the air cooling. The multiple jet experiments were performed using air jet velocities between 40 and 90 m/s containing low mass flux of water mist that was varied from 0 up to 0.145 kg/m2 s for each jet. The experiments include different glass thicknesses. The optimal tempering conditions were explored.
The mechanisms of mist cooling are revealed from the experiments of a single water mist jet impinging on hot stainless steel plates. Since the droplets are small, of the order of 22 μm, heat transfer distribution of the water mist has a similar form as the air jet cooling. The total heat transfer coefficient can be viewed as two separable effects: the summation of the heat transfer coefficient of the convective air and of the impinging water flux, respectively. The heat transfer of multiple water mist jets on larger glass is studied. The mist cooling demonstrates a define saving in the use of high-pressure air. When using mist cooling, the energy requirements of the system are significantly lowered. The mist cooling creates more refined fracturing in the punching tests of tempered glass. For glass thicker than 3 mm, the particle counts due to water mist improve about 121%. The improvement is about 38% for 2-mm glass. The test results indicate that thin and low-cost tempered glass can be made by mist cooling without fracture and with about 29% air pressure reduction for 2-mm glass plate and 50% reduction for both 3-mm and 4-mm glass plates.


Articles with similar content:

INFLUENCE OF SURFACE WETTABILITY ON HEAT TRANSFER AND PRESSURE DROP CHARACTERISTICS OF WET AIR IN METAL FOAM UNDER DEHUMIDIFYING CONDITIONS
International Heat Transfer Conference 16, Vol.14, 2018, issue
GuoLiang Ding, Zhancheng Lai, Haitao Hu
GASOLINE INJECTION AGAINST SURFACES AND FILMS
Atomization and Sprays, Vol.7, 1997, issue 4
D. S. Whitelaw, Jim H. Whitelaw, C. Arcoumanis
UNDERSTANDING OF SUSPENSION PLASMA SPRAYING
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.8, 2004, issue 1
J. F. Coudert, J. Fazilleau, C. Delbos, C. Bonhomme, Pierre Fauchais, V. Rat
DRILLING CUTTINGS TRANSPORT IN HORIZONTAL WELLS WHILE AERATED DRILLING
4th Thermal and Fluids Engineering Conference, Vol.11, 2019, issue
Ibrahim Hassan, Mohammad Azizur Rahman, Golam Rasul, Stephen Butt, Rashid Hasan
PLASMA PROCESSING OF CONCRETE AND RELATED MATERIALS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.11, 2007, issue 4
B. Dzur