Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v7.i1.60
pages 115-122

SPRAY SYNTHESIS OF SUPERPLASTIC MATERIALS FOR NEAR-NET-SHAPE MANUFACTURING

Yue Wu
Department of Chemical Engineering and Materials Science, University of California, Irvine, СА 92717
Enrique J. Lavernia
Department of Chemical Engineering and Materials Science, University of California, Irvine, California, 92717, USA

RESUMO

Spray deposition was used to synthesize 5083 Al alloy with N2 and N2 + O2 mixture as atomization gases. The starting 5083 Al was alloyed with Zr during spray deposition in order to refine grain size. It was noted that the grains that were present in as-spray deposited 5083 Al were equiaxed. In the inert gas spray deposited alloys, grain size decreased with increasing Zr content. Reactive spray deposition using N2 + O2 mixture, however, led to an increase in average grain size which is considered a result of release of enthalpy during oxidation reaction of matrix alloys. The spray deposited alloys were thermomechanically processed using extrusion and multiple-pass warm rolling to further reduce grain size. Superplasticity was observed in the 500−550 °C temperature range for strain rates between 3 × 10−5 and 3 × 10−3 s−1. A maximum elongation of 465% was noted at 550% and 3 × 10−5 s−1. The spray deposited alloys thermomechanically processed by direct rolling, exhibited superplasticity in the same temperature and strain rate ranges as those for the extruded and rolled materials. The superplastic elongation of the spray formed and rolled material was relatively low, being in the range of 180 ∼ 260%.


Articles with similar content:

GROWTH OF NANOCRYSTALLYTES IN A Ge-Se AMORPHOUS THIN FILM
Nanoscience and Technology: An International Journal, Vol.2, 2011, issue 1
E. V. Aleksandrovich, E. V. Stepanova, A. V. Vakhrushev
INFLUENCE OF MODIFYING ADDITIVES ON THE PHASE STABILITY AND RESISTANCE TO OXIDATION OF COATINGS BASED ON STABILIZED ZIRCONIUM DIOXIDE AND A CARBON−CARBON COMPOSITE MATERIAL
Nanoscience and Technology: An International Journal, Vol.7, 2016, issue 4
D. Yu. Sinitsyn, V. N. Anikin, S. A. Eremin, B. V. Ryabenko
WEAR RESISTANCE AND RADIATION TOLERANCE OF He+-IRRADIATED MAGNETRON SPUTTERED TiAlN COATINGS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.18, 2014, issue 1-2
F. F. Komarov, Stanislav Konstantinov, V. V. Pilko, V. A. Kukareko
SYNTHESIS, CHARACTERIZATION, AND REACTION KINETICS OF NANO-STRUCTURED Mg−V−Ni COMPOSITES FOR SOLID-STATE HYDROGEN STORAGE
International Journal of Energetic Materials and Chemical Propulsion, Vol.11, 2012, issue 3
K. G. Bambhaniya, G. S. Grewal, N. L. Singh, Vagish Shrinet, T. P. Govindan
RELEVANT PARAMETERS FOR LASER BONDING OF COPPER ON ALUMINA
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.10, 2006, issue 2
J. C. Labbe, Pierre Lefort, J. Jarrige, S. Menecier