Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v10.i2.50
19 pages

CHARACTERIZATION OF PROTOTYPE HIGH-PRESSURE SWIRL INJECTOR NOZZLES, PART II: CFD EVALUATION OF INTERNAL FLOW

Changsoo Jang
Department of Mechanical Engineering, KAIST, Taejon, Korea
Choongsik Bae
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Gusong-dong, Yuseong-gu, Daejon, 305-701, Republic of Korea
Sangmin Choi
Department of Mechanical Engineering, Korea Advanced Institute of Science and Technology, Yusong-gu, Taejon, Korea

RESUMO

Static flow rate and initial cone angle of high-pressure swirl injector nozzles were characterized through measurements and computations as a preliminary optimization process of nozzle design. Prototype injectors were fabricated by modifying commercial multipoint injection (MPI) nozzles. Measurements of static flow rate were compared with the computations, and the agreements were satisfactory in values and tendencies with respect to the nozzle geometry and the needle lift. Initial cone angle was calculated and compared with measurements by the direct photographic imaging method. It could be predicted satisfactorily by introducing an adequate correction factor. Considering these cross-checking for a validation of the computational model, a parametric study was carried out to predict the flow rate and the initial cone angle with respect to selected design parameters.


Articles with similar content:

Swirl Atomizer Design for Evaporative Cooling of High Temperature Compressed Air Stream
International Journal of Fluid Mechanics Research, Vol.41, 2014, issue 1
Uzair Ahmed Dar, Mykola Bannikov
EXPERIMENTAL AND COMPUTATIONAL STUDY OF THE INFLUENCE OF PARTIAL NEEDLE LIFT ON NOZZLE FLOWIN DIESEL FUEL INJECTORS
Atomization and Sprays, Vol.22, 2012, issue 8
Jaime Gimeno, Raul Payri, Alejandro H. Plazas, O. Venegas
Studies on Swirl Hole Nozzle using ANOVA
International Journal of Fluid Mechanics Research, Vol.38, 2011, issue 6
Himadri Chattopadhyay, Subrata. K. Mandal
ANALYSIS OF SIZE-CLASSIFIED SPRAY STRUCTURE AND ATOMIZATION MECHANISM FOR A GASOLINE DIRECT INJECTOR
Atomization and Sprays, Vol.14, 2004, issue 6
Chang Sik Lee, Chang Hee Lee
CHARACTERIZATION OF HIGH-INJECTION-PRESSURE DIESEL SPRAYS WITH RELATION TO PARTICULATE AND NOx EMISSIONS
Atomization and Sprays, Vol.8, 1998, issue 1
T. F. Su, Patrick V. Farrell