Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2012003917
pages 971-987

INTERNAL FLOW CHARACTERISTICS OF LIQUID-LIQUID SWIRL COAXIAL INJECTORS WITH DIFFERENT RECESS LENGTHS AND OXIDIZER-FUEL RATIOS

Sunghyuk Kim
Institute of Advanced Aerospace Technology, School of Mechanical and Aerospace Engineering, Seoul National University, San 56-1, Shillim-dong, Gwanak-gu, Seoul, 151-742, KOREA
Jungsoo Yoon
School of Mechanical and Aerospace Engineering, Seoul National University, 599 Gwanak-ro, Gwanak-gu, Seoul, 151-742, Korea
Youngbin Yoon
Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul, 08826, Republic of Korea

RESUMO

In this study, the aim is to investigate the internal flow characteristics related to the oxidizer−fuel (O/F) ratio of a recessed swirl coaxial injector for gas generators and main combustors in liquid rocket engines. The mixing process of internal flow is very important in a recessed swirl coaxial injector; however, measuring internal flow is almost impossible except if using numerical analysis. This paper describes the design of a swirl coaxial injector that enables flow visualization and film thickness measurement and gives the results of cold flow tests using water as a simulant fluid. The injection conditions in the injector for the gas generator and main combustor were set to O/F ratios of 0.32 and 2.44 and the off-design points were set to 10% and 15%, respectively. Recess length varied by 1 mm for each case. The liquid film thickness variations after collision between two liquid flows were measured using the electrical conductance method. In addition, the characteristics of liquid film wave frequency and amplitude were analyzed based on liquid film thickness measurement and mixing time. This study confirms that liquid film becomes thinner after the mixing process. This is based on visualizing the internal flow and measuring liquid film thickness. The degree of the thinning of the liquid film varies with the momentum flux ratio according to the O/F ratio. An unstable internal flow was detected in the mixing process near the injector tip position.


Articles with similar content:

GEOMETRIC EFFECT ON SPRAY CHARACTERISTICS OF GAS-CENTERED SWIRL COAXIAL INJECTORS: RECESS RATIO AND GAP THICKNESS
Atomization and Sprays, Vol.27, 2017, issue 7
Jungho Lee, Chae Hoon Sohn, Youngbin Yoon, Ingyu Lee, Gujoeng Park
EFFECT OF RECESS ON MIXING AND ATOMIZATION CHARACTERISTICS OF LIQUID-LIQUID SWIRL COAXIAL INJECTORS
Atomization and Sprays, Vol.20, 2010, issue 1
Poonggyoo Han, Sunghyuk Kim, Youngbin Yoon, Dongjun Kim
SPRAY VISUALIZATION AND HYDRAULIC CHARACTERIZATION OF THE HOLES OF A FIVE-HOLE, VALVE-COVERED-ORIFICE NOZZLE OF AN ELECTRONICALLY CONTROLLED DIESEL INJECTOR
Atomization and Sprays, Vol.6, 1996, issue 3
D. Laforgia, V. Damiani, R. Campanella
Effects of the Internal Flow in a Nozzle Hole on the Breakup Processes of a Liquid Jet
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 4-6
Keiya Nishida, Hiroyuki Hiroyasu, N. Tamaki, M. Shimizu
SELF-PULSATION CHARACTERISTICS OF A GAS-LIQUID SWIRL COAXIAL INJECTOR
Atomization and Sprays, Vol.19, 2009, issue 1
Poonggyoo Han, Vladimir Bazarov, Ji-Hyuk Im, Youngbin Yoon, Dongjun Kim