Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2014010767
pages 827-840

SPRAY OF POWER-LAW FLUID FROM A SWIRL INJECTOR WITH NONTANGENTIAL INLET CHANNELS

Qing-Fei Fu
School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing, 100191, China; School of Mechanical, Aerospace and Civil Engineering, The University of Manchester, Manchester M13 9PL, United Kingdom
Kun-Da Cui
School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing, China, 100191

RESUMO

The spray formation of power-law non-Newtonian liquids from swirl injectors with nontangential inlet channels was described by carrying out experiments in a spray test facility and compared with the spray behavior from common swirl injectors. The most evident difference between the two types of injectors is that the spray cone pulsated for the swirl injectors with nontangential inlets. The pulsation is caused by the compressible air remaining in the swirl chamber, which can reduce the sheet breakup length under high pressure drop. The nontangential entry of liquids into the swirl chamber eventually reduces the fluid swirl radius, and the equivalent geometric characteristics constant decreases. As a result, the spray angle would decrease, and the mass flow rate would increase.


Articles with similar content:

SPRAY CHARACTERISTICS OF AN OPEN-END SWIRL INJECTOR
Atomization and Sprays, Vol.22, 2012, issue 5
Wei Zhang, Qing-Fei Fu, Kun-Da Cui, Li-Jun Yang
ROLE OF GEOMETRIC PARAMETERS ON THE DROP SIZE CHARACTERISTICS OF LIQUID-LIQUID COAXIAL SWIRL ATOMIZERS
Atomization and Sprays, Vol.8, 1998, issue 5
D. Sivakumar, B. N. Raghunandan
PRELIMINARY INVESTIGATION ON THE SPREADING ANGLE OF A NEAR-CRITICAL RP-3 KEROSENE JET
Atomization and Sprays, Vol.25, 2015, issue 11
Zhencen Fan, Wei Fan, Le Jin, Zhou Zhou, Jin Zhang
SPRAY BEHAVIOR IN NONSWIRUNG AND SWIRLING ANNULAR AIR FLOWS
Atomization and Sprays, Vol.1, 1991, issue 3
Xianguo Li, R. S. Tankin
EFFECT OF NOZZLE GEOMETRY ON BREAKUP LENGTH AND TRAJECTORY OF LIQUID JET IN SUBSONIC CROSSFLOW
Atomization and Sprays, Vol.21, 2011, issue 10
Baafour Nyantekyi-Kwakye, Madjid Birouk, Neil Popplewell