Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015012537
pages 1013-1024

DYNAMICS OF CLEANING BY HYDRAULIC PULSED JET

Shuang Liu
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing, 102249, P.R. China
Gensheng Li
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing, P.R. China
Huaizhong Shi
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing, 102249, China
Zhongwei Huang
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum (Beijing), Beijing 102249, PR. China
Shouceng Tian
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing 102249, China
Ruiyue Yang
State Key Laboratory of Petroleum Resources and Prospecting, China University of Petroleum, Beijing, 102249, P.R. China

RESUMO

Because of its cleaning and cutting capabilities, hydraulic pulsed jet technology is considered to be a highly efficient method for improving the rate of penetration. Although adequate removal of cuttings from the bottom hole is important for efficient drilling operations, very little basic research is available concerning the fundamentals of chip removal by the hydraulic pulsed jet. Therefore, this paper presents a discussion of a numerical simulation investigation for the performance of a pulsed jet in removing loose particles. The cleaning effects of a pulsed jet and continuous jet were compared, and the parametric influence analysis of particle size, frequency, and nozzle size was performed. The results show that the cleaning effect of the pulsed jet is better than that of the continuous jet under the same conditions, especially for larger particles. Under the given conditions, the relatively low-frequency pulsed jet (about 10 Hz) is more efficient to remove chips. The cleaning effect of the pulsed jet improves with the growth of the particle size and nozzle size. The system studied in the paper is not directly applicable to a real drilling bit. However, the work done with such a simplified system can provide a better understanding of the process of chip removal by the pulsed jet, and the influencing parameters. This work may also provide a reasonable basis for the use of pulsed jet methods in drilling.


Articles with similar content:

THERMAL TRANSPORT IN THE MANUFACTURE OF OPTICAL FIBERS
Annual Review of Heat Transfer, Vol.20, 2017, issue 1
Yogesh Jaluria
Experimental Investigation of WaterWave Characteristics in aWave Channel
International Journal of Fluid Mechanics Research, Vol.38, 2011, issue 2
M. Rafiuddin Ahmed, Mohammed Faizal, Chang-Goo Kim, Young-Ho Lee
A Study of the Injection of Twin Pulsed High Speed Liquid Jets Across Transonic Region
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 4-6
Motoyuki Itoh, H.-H. Shi
OPTICAL TESTING OF LAYERED MICROSTRUCTURES WITH AND WITHOUT UNDERLYING VIAS
International Heat Transfer Conference 13, Vol.0, 2006, issue
Leslie M. Phinney, J. R. Serrano
Respiration Activity of the Green Alga Desmodesmus Communis (Hegew.) Hegew. under the Influence of the Ions of Zinc
Hydrobiological Journal, Vol.44, 2008, issue 2
O. I. Bodnar, V. V. Grubinko