Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v21.i1.20
pages 17-29

Geometric Primary Atomization Characteristics in an Airblast Atomizer, High Pressure Conditions

Vital Gutierrez Fernandez
Heterogeneous, Multiphase Flows Unit, Aerodynamic and Energetic Models Department, Office National d'Etudes et de la Recherche Aérospatiales (ONERA), Toulouse, France
G. Lavergne
Heterogeneous, Multiphase Flows Unit, Aerodynamic and Energetic Models Department, Office National d'Etudes et de la Recherche Aérospatiales (ONERA), 31055 Toulouse Cedex 4, France
P. Berthoumieu
Heterogeneous, Multiphase Flows Unit, Aerodynamic and Energetic Models Department, Office National d'Etudes et de la Recherche Aérospatiales (ONERA), 31055 Toulouse Cedex 4, France

RESUMO

An experimental study via fast camera visualizations was accomplished to analyze the primary atomization. The injection device consisted in a planar airblast atomizer, which generated a 300μm thickness liquid sheet. The system considered, kept its geometry constant, while the fluids flow was modified to produce a wide range of conditions. This was achieved by adjusting the fluids' momentum flux. In the case of the gas, both the air velocity across the airblast atomizer and its absolute pressure were varied. The latter parameter reached a value of 11 bar. Additionally, two liquids, water and Kerosene Jet A1 were injected at several velocities. The manuscript includes results for the break-up length, transversal wavelength, and longitudinal ligaments length. The behaviour of these characteristics was strongly affected by the atomization mechanism at which they were measured. Consequently, a set of image proceses techniques were developed to measure these characteristics. Finally, a set of empirical relsations are proposed to predict the magnitude of these characteristics at the tested conditions.


Articles with similar content:

Dynamic Primary Atomization Characteristics in an Airblast Atomizer, High Pressure Conditions
Atomization and Sprays, Vol.21, 2011, issue 1
Vital Gutierrez Fernandez, P. Berthoumieu, G. Lavergne
ATOMIZATION OF HIGH-VISCOSITY AND NON-NEWTONIAN FLUIDS BY PREMIXING
Atomization and Sprays, Vol.28, 2018, issue 5
Volfango Bertola, Michele Negri, Tom Baker
Experimental Study of Primary Break-up of Liquid Jets in Cross Airflows
International Heat Transfer Conference 12, Vol.32, 2002, issue
Thomas Stabler, Barry J. Azzopardi, Madjid Birouk
SPRAY BEHAVIOR OF THE ROTARY ATOMIZER WITH IN-LINE INJECTION ORIFICES
Atomization and Sprays, Vol.20, 2010, issue 10
Seong Ho Jang, Seong Man Choi
THE PERFORMANCE CHARACTERISTICS OF SOLID-CONE-SPRAY PRESSURE-SWIRL ATOMIZERS
Atomization and Sprays, Vol.10, 2000, issue 6
D. D. James, J. R. Jeong, R. A. Sharief