Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.262 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v21.i1.30
pages 31-40

CFD Study of Needle Motion Influence on the Spray Conditions of Single-Hole Injectors

Xandra Margot
CMT-Motores Térmicos Edificio 6D Universitat Politècnica de València Camino de Vera s/n 46022 Valencia. Spain
Sergio Hoyas
School of Aeronautics, Universidad Politecnica de Madrid 28040 Madrid, Spain; CMT - Motores Térmicos, Universidad Politécnica de Valencia, Camino de Vera S/N, 46022 Valencia, Spain
P. Fajardo
CMT - Motores Térmicos, Universidad Politécnica de Valencia, Camino de Vera S/N, 46022 Valencia, Spain
S. Patouna
CMT - Motores Térmicos, Universidad Politécnica de Valencia, Camino de Vera S/N, 46022 Valencia, Spain

RESUMO

The spray characteristics and consequently the success of the diesel combustion process is strongly affected by the manner in which fuel is introduced in the combustion chamber. This work consists in studying the effect of needle motion of typical single-hole sac-type injectors on nozzle exit conditions. Three-dimensional moving mesh simulations have been carried out to calculate the injection process using cylindrical and conical nozzle geometries. The CFD analysis includes a study of the effect of cavitation on kinetic turbulent energy and velocity profiles. Results show that the flow within the nozzle and at the exit varies depending on the nozzle geometry and needle position. The model predicts clouds of cavitation that grow and exit the nozzle at low needle lifts. A kind of hysteresis in the development of the flow has also been observed between needle opening and closing. The existing correlation between turbulence and cavitation at the nozzle hole exit during the needle motion has been quantified.


Articles with similar content:

A CFD ANALYSIS OF THE INFLUENCE OF DIESEL NOZZLE GEOMETRY ON THE INCEPTION OF CAVITATION
Atomization and Sprays, Vol.13, 2003, issue 5&6
F. J. Salvador, Raul Payri, Xandra Margot, V. Macian
NUMERICAL ANALYSIS OF THE INFLUENCE OF DIESEL NOZZLE DESIGN ON INTERNAL FLOW CHARACTERISTICS FOR 2-VALVE DIESEL ENGINE APPLICATION
Atomization and Sprays, Vol.23, 2013, issue 2
Joaquin De la Morena, Kshitij Neroorkar, Alejandro H. Plazas, David P. Schmidt, Richard C. Peterson
ANALYSIS OF TRANSIENT LIQUID AND VAPOR PHASE PENETRATION FOR DIESEL SPRAYS UNDER VARIABLE INJECTION CONDITIONS
Atomization and Sprays, Vol.21, 2011, issue 6
Raul Payri, Francisco J. Briceno, Jose M. Garcia-Oliver, Jose V. Pastor
NUMERICAL MODELS FOR SIMULATION OF CAVITATION IN DIESEL INJECTOR NOZZLES
Atomization and Sprays, Vol.25, 2015, issue 12
Akira Sou, Baris Bicer
FORMATION AND DEVELOPMENT OF WALL LIQUID FILMS DURING IMPACTION OF GASOLINE FUEL SPRAYS
Atomization and Sprays, Vol.19, 2009, issue 8
Maria Spathopoulou, Manolis Gavaises, Hiromichi Yanagihara, Andreas P. Theodorakakos