Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Heat Pipe Science and Technology, An International Journal

ISSN Печать: 2151-7975
ISSN Онлайн: 2151-7991

Archives: Volume 1, 2010 to Volume 8, 2017

Heat Pipe Science and Technology, An International Journal

DOI: 10.1615/HeatPipeScieTech.v5.i1-4.790
pages 681-688

AN EXPERIMENTAL INVESTIGATION OF PHASE CHANGE MATERIAL (PCM) FOR HEAT MANAGEMENT OF INSTRUMENTS

Pankaj Srivastava
Instrument research and Development Establishment, Defense Research and Development Organization, Dehradun, 248008 India
A. K. Sahani
Instrument research and Development Establishment, Defense Research and Development Organization, Dehradun, 248008 India
J. K. Bajpai
Instrument research and Development Establishment, Defense Research and Development Organization, Dehradun, 248008 India
Sameer Khandekar
Department of Mechanical Engineering, Indian Institute of Technology Kanpur, Kanpur (UP) 208016, India

Краткое описание

This paper presents an experimental investigation of passive cooling of instruments using phase change material and heat pipe. Instruments for defence and surveillance consist of one or more electro-optical sensors, which generate heat continuously or/and intermittently. Heat generated by these sensors is required to be dissipated from sealed enclosure to ambient. To simulate the actual condition for intermittent heat generating unit, a constant heat source is applied inside enclosure. Heat pipe is connected to heat source for heat transfer to ambient. Since performance of heat pipe is greatly dependent on the cooling mechanism at condenser side, active fan is required for better performance. For passive cooling PCM may be a substitute of active fan for intermittent heat source as molten PCM needs to be re-solidified by dissipating heat to surrounding while. PCM which is stored between the fins of heat sink is applied outside the enclosure. Properties of PCM including the melting temperature of 48-50°C, latent heat, sensible heat, thermal conductivity and density are based on a commercially available paraffin wax. The experimental result shows that PCM is also very useful to enhance duty cycle of intermittent use as well as it restricts maximum temperature at condenser end. To achieve effective cooling it is important to ensure that the operating duration of the electronic devices does not exceed the time of full melting.


Articles with similar content:

THERMAL ENERGY STORAGE WITH TUNABLE MELTING POINT PHASE CHANGE MATERIALS
International Heat Transfer Conference 16, Vol.12, 2018, issue
Richard Bonner, Fangyu Cao, Ying Zheng, Chien-Hua Chen
NON-REGENERATIVE MULTI-STAGE AND REGENERATIVE MULTI-BED ADSORPTION CYCLES FOR LOW-TEMPERATURE WASTE HEAT RECOVERY
Proceedings of Symposium on Energy Engineering in the 21st Century (SEE2000) Volume I-IV, Vol.0, 2000, issue
Kim Choon Ng, Bidyut Baran Saha, Takao Kashiwagi, Hui Tong Chua, Atsushi Akisawa
EFFECT OF VOLUME OF EVAPORATOR AND BED HEAT EXCHANGER ON PERFORMANCE OF ADSORPTION CHILLER
3rd Thermal and Fluids Engineering Conference (TFEC), Vol.26, 2018, issue
Gamze Gediz Ilis, Hasan Demir
COOLING OF A CONCENTRATED PHOTOVOLTAIC CELL USING HEAT PIPES
Heat Pipe Science and Technology, An International Journal, Vol.5, 2014, issue 1-4
Sang Min Kim, Joon Hong Boo, Jae Hyuk Shin, Seung Shin Yi
EXPERIMENTAL AND ANALYTICAL INVESTIGATION OF THERMAL MANAGEMENT OF LED ASSEMBLIES USING MICRO-HEAT COOLING DEVICES
Heat Transfer Research, Vol.50, 2019, issue 13
Cheng-Wu Liu, Tzu-Hsuan Chien, Ming-Der Jean, Peng-Da Lei