Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Journal of Enhanced Heat Transfer
Импакт фактор: 1.406 5-летний Импакт фактор: 1.075 SJR: 0.287 SNIP: 0.653 CiteScore™: 1.2

ISSN Печать: 1065-5131
ISSN Онлайн: 1026-5511

Выпуски:
Том 27, 2020 Том 26, 2019 Том 25, 2018 Том 24, 2017 Том 23, 2016 Том 22, 2015 Том 21, 2014 Том 20, 2013 Том 19, 2012 Том 18, 2011 Том 17, 2010 Том 16, 2009 Том 15, 2008 Том 14, 2007 Том 13, 2006 Том 12, 2005 Том 11, 2004 Том 10, 2003 Том 9, 2002 Том 8, 2001 Том 7, 2000 Том 6, 1999 Том 5, 1998 Том 4, 1997 Том 3, 1996 Том 2, 1995 Том 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.2013006771
pages 267-275

EXPERIMENTAL INVESTIGATION OF CONVECTION HEAT TRANSFER FROM OPEN-CELLED METAL FOAM BLOCKS

Ayla Dogan
Department of Mechanical Engineering, Faculty of Engineering, Akdeniz University TR-07058, Antalya, Turkey
Tugce Tezel
Department of Mechanical Engineering, Faculty of Engineering, Akdeniz University, TR-07058 Antalya, Turkey

Краткое описание

In this paper, an experimental study was conducted to investigate the convection heat transfer inside a horizontal rectangular channel where open-celled aluminum-foam blocks with different pore densities [10, 20, and 40 pores per inch (PPI)] are located. Air was used as the working fluid. The lower surface of the channel was equipped with 8 × 2 arrays of aluminum-foam blocks subjected to uniformheat flux. All remaining surfaces were insulated. The experimental parametric study was made for foam aspect ratios (ARs) of 0.25, 0.5, and 0.75 at various Reynolds and Grashof numbers. The Reynolds number, based on the channel hydraulic diameter of the rectangular channel, was varied from 497 to 7807, while the Grashof number ranged from 4.3 × 107 to 2.9 × 108. The effects of the pore density and aluminum-foam AR are reported. The results obtained show that the row-averaged Nusselt number increases with decreasing pore density, and with increasing AR of the foam blocks. For AR = 0.75, the thermal performance of the aluminum foam with a pore density of 10 PPI is about 51.1 and 85.4% higher than for 20 and 40 PPI, respectively.


Articles with similar content:

HEAT TRANSFER IN A CHANNEL WITH INTERMITTENT HEATED ALUMINUM-FOAM HEAT SINKS
Heat Transfer Research, Vol.48, 2017, issue 3
Ayla Dogan, Bahadir Oney
EXPERIMENTAL INVESTIGATION OF NATURAL CONVECTION FROM POROUS BLOCKS IN A CAVITY
Journal of Porous Media, Vol.19, 2016, issue 12
Ayla Dogan, O. Ozbalci, I. Atmaca
NATURAL CONVECTION HEAT TRANSFER FROM SQUARE PIN FIN AND PLATE FIN HEAT SINKS SUBJECT TO THE INFLUENCE OF ORIENTATION
International Heat Transfer Conference 13, Vol.0, 2006, issue
R. T. Huang, Chi-Chuan Wang, Wen-Jenn Sheu
Heat Transfer Performance of a Channel Flow with Aluminum Fiber Layers (Comparison with Aluminum Porous Foams)
International Heat Transfer Conference 15, Vol.23, 2014, issue
Masaaki Sakagami, Kyoji Inaoka, Mami Yamamoto, Mamoru Senda, Keita Imai
EFFECT OF ASPECT RATIO ON EVAPORATION HEAT TRANSFER AND PRESSURE DROP OF R-410A IN FLATTENED MICROFIN TUBES
Journal of Enhanced Heat Transfer, Vol.22, 2015, issue 3
Nae-Hyun Kim