Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Journal of Enhanced Heat Transfer
Импакт фактор: 1.406 5-летний Импакт фактор: 1.075 SJR: 0.287 SNIP: 0.653 CiteScore™: 1.2

ISSN Печать: 1065-5131
ISSN Онлайн: 1563-5074

Выпуски:
Том 27, 2020 Том 26, 2019 Том 25, 2018 Том 24, 2017 Том 23, 2016 Том 22, 2015 Том 21, 2014 Том 20, 2013 Том 19, 2012 Том 18, 2011 Том 17, 2010 Том 16, 2009 Том 15, 2008 Том 14, 2007 Том 13, 2006 Том 12, 2005 Том 11, 2004 Том 10, 2003 Том 9, 2002 Том 8, 2001 Том 7, 2000 Том 6, 1999 Том 5, 1998 Том 4, 1997 Том 3, 1996 Том 2, 1995 Том 1, 1994

Journal of Enhanced Heat Transfer

DOI: 10.1615/JEnhHeatTransf.v24.i1-6.190
pages 361-372

BOILING HEAT TRANSFER FROM A SILICON CHIP IMMERSED IN DEGASSED AND GAS-DISSOLVED FC-72: EFFECTED BY SIZE AND NUMBER DENSITY OF MICRO-REENTRANT CAVITIES

H. Kubo
Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka 816-8580, Japan
Hiroshi Takamatsu
Department of Mechanical Engineering, Kyushu University, Fukuoka 819-0395, Japan
Hiroshi Honda
Institute of Advanced Material Study, Kyushu University, Kasuga, Fukuoka 816-8580, Japan

Краткое описание

Boiling heat transfer of FC-72 from newly developed treated surfaces with micro-reentrant cavities was studied experimentally. The surface structure was fabricated on a silicon chip by use of microelectronic fabrication techniques. Four kinds of treated surfaces with the combinations of two cavity mouth diameters (about 1.6 μm and 3.1 μm) and two number densities of the micro-reentrant cavities (81 l/cm2 and 96 × 103 l/cm2) were tested along with a smooth surface. Experiments were conducted at the liquid subcoolings of 3 K and 25 K with degassed and gas-dissolved FC-72. While the wall superheat at boiling incipience was strongly dependent on the dissolved gas content; it was little affected by the cavity mouth diameter and the liquid subcooling. The heat transfer performance of the treated surface was considerably higher than that of the smooth surface. The highest performance was obtained with a treated surface with a larger cavity mouth diameter and a larger cavity number density. The results were compared with those for previously developed treated surfaces.


Articles with similar content:

Effects of Size and Number Density of Micro-reentrant Cavities on Boiling Heat Transfer from a Silicon Chip Immersed in Degassed and Gas-dissolved FC-72
Journal of Enhanced Heat Transfer, Vol.6, 1999, issue 2-4
Hiroshi Takamatsu, Hiroshi Honda, H. Kubo
NUCLEATE AND FILM BOILING HEAT TRANSFER IN R11: THE EFFECTS OF ENHANCED SURFACES AND INCLINATION
International Heat Transfer Conference 8, Vol.4, 1986, issue
D. S. Jung, James E. S. Venart, Antonio C. M. Sousa
Enhanced Boiling Heat Transfer from Silicon Chips with Micro-Pin Fins Immersed in FC-72
Journal of Enhanced Heat Transfer, Vol.10, 2003, issue 2
Hiroshi Takamatsu, Hiroshi Honda, Jin Jia Wei
HEAT TRANSFER ENHANCEMENT OF SURFACES FOR POOL BOILING USING ADDITIVE MANUFACTURING
First Thermal and Fluids Engineering Summer Conference, Vol.8, 2015, issue
Kin Keong Wong, Kai Choong Leong, S. B. Tor
Improvement of Nucleate Boiling Heat Transfer Characteristics by Using Immiscible Mixtures
International Heat Transfer Conference 15, Vol.38, 2014, issue
Shunsuke Onishi, Haruhiko Ohta, Yuta Fukuyama, Shota Kita