High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
Выходит 4 номеров в год
ISSN Печать: 1093-3611
ISSN Онлайн: 1940-4360
IF:
0.4
Immediacy Index:
0.1
Eigenfactor:
0.00005
JCI:
0.07
SJR:
0.198
SNIP:
0.48
CiteScore™::
1.1
H-Index:
20
Indexed in
Том 3, 1999 Выпуск 1
DOI: 10.1615/HighTempMatProc.v3.i1
SOME ASPECTS OF ALLOYING AND REFINING OF HIGH NITROGEN STEELS IN A PLASMA FURNACE UNDER ELEVATED PRESSURE
pp. 17-24
DOI: 10.1615/HighTempMatProc.v3.i1.20
RADIATION EMISSION OF THERMAL PLASMA IN 02, H20, C02 AND AIR
pp. 25-37
DOI: 10.1615/HighTempMatProc.v3.i1.30
ABOUT ROTATIONAL TEMPERATURE MEASUREMENTS AND THERMODYNAMIC EQUILIBRIUM IN RF GLOW DISCHARGES
pp. 39-50
DOI: 10.1615/HighTempMatProc.v3.i1.40
MOLTEN SALT REACTOR TECHNOLOGY FOR SEPARATION AND TRANSMUTATION
pp. 51-66
DOI: 10.1615/HighTempMatProc.v3.i1.50
Thermodynamic Assessment of the NaCl-DyCl3 Molten Salt System
pp. 77-89
DOI: 10.1615/HighTempMatProc.v3.i1.70
Effect of High Polarizability on Mobilities in Ionic Melts
pp. 105-116
DOI: 10.1615/HighTempMatProc.v3.i1.90
Morphology of Titanium Diboride Obtained by Electrochemical Synthesis from Molten Chloro-Fluoride Melt
pp. 117-124
DOI: 10.1615/HighTempMatProc.v3.i1.100
Phase Diagram Systematic Optimization of the REI2-MI (RE = Sm, Eu, Yb, M= Li, Na, K, Rb, Cs) Systems
pp. 125-140
DOI: 10.1615/HighTempMatProc.v3.i1.110
Последний выпуск
DETERMINATION OF THE MASS BALANCE OF HIGH-CARBON FERROCHROME IN A SUBMERGED ARC FURNACE
RHEOLOGICAL BEHAVIOR AND 3D PRINTING OF HIGHLY FILLED ALUMINA-POLYAMIDE FILAMENTS DURING FUSED DEPOSITION MODELING
SCRATCH TESTING OF ZrN COATING ON TI-6AL-4V TITANIUM ALLOY SURFACE PRELIMINARY TREATED BY COMPRESSION PLASMA FLOWS IMPACT
ELECTRON-BEAM SINTERING OF ZIRCONIUM DIOXIDE/TITANIUM CERAMICS FOR MICROELECTRONICS PRODUCTS
THE EFFECT OF THE FLUORINE CONCENTRATION IN A PLASMA-FORMING GAS MIXTURE ON THE CHEMICAL COMPOSITION, SURFACE CHARGE, AND RELIEF PARAMETERS OF FLUOROCARBON COATINGS ON PET
PREPARATION AND THERMOELECTRIC PROPERTIES OF p-TYPE Ag(1-x)Cu(1+x)Te SAMPLES BY SPARK PLASMA SINTERING METHOD
ELECTRON-BEAM SYNTHESIS OF ZIRCONIA CERAMIC COATINGS IN THE FOREVACUUM PRESSURE RANGE
INCREASING THE WEAR RESISTANCE OF TITANIUM ALLOYS BY DEPOSITION OF A MODIFYING COATING (Zr,Nb)N
PHYSICAL AND MECHANICAL PROPERTIES AND OPERATIONAL CHARACTERISTICS OF CORONA SPRAYED POWDER COATINGS
Статьи, принятые к публикации
Application of a non-self-sustained glow discharge initiated by a focused electron beam in the forevacuum pressure region for nitriding the inner surface of narrow metal tubes
PLASMA DISCHARGE IN LIQUID MEDIA UNDER THE EFFECT OF ULTRASOUND FOR THE SYNTHESIS OF FILLERS FOR POLYMER COMPOSITES WITH ENHANCED MECHANICAL STRENGTH AND GAS PERMEABILITY
THE QUALITY OF THIN-WALLED STRUCTURES OF AlSi10Mg PRODUCED BY SELECTIVE LASER MELTING
Electron-beam synthesis of zirconia ceramic coatings in the forevacuum pressure range
Preparation and Thermoelectric Properties of P-type Ag(1-x)Cu(1+x)Te Samples by SPS Method
The effect of the fluorine concentration in a plasma-forming gas mixture on the chemical composition, surface charge and relief parameters of fluorocarbon coatings on PET
Electron beam sintering of zirconium dioxide/titanium ceramics for microelectronics products