Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
ESCI SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Печать: 1093-3611
ISSN Онлайн: 1940-4360

Выпуски:
Том 24, 2020 Том 23, 2019 Том 22, 2018 Том 21, 2017 Том 20, 2016 Том 19, 2015 Том 18, 2014 Том 17, 2013 Том 16, 2012 Том 15, 2011 Том 14, 2010 Том 13, 2009 Том 12, 2008 Том 11, 2007 Том 10, 2006 Том 9, 2005 Том 8, 2004 Том 7, 2003 Том 6, 2002 Том 5, 2001 Том 4, 2000 Том 3, 1999 Том 2, 1998 Том 1, 1997

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v13.i3-4.10
pages 247-265

DYNAMICS OF PARTICLE DEFORMATION DURING PLASMA SPRAY COATING

Sanjeev Chandra
Center for Advanced Coating Technologies, Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, Ontario, Canada, M5S 3G8
Rajeev Dhiman
Centre for Advanced Coatings Technologies, Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, Ontario

Краткое описание

Molten droplets during plasma spray process either fragment during impact or form intact, disk-like splats. Splat break-up produces coatings with low adhesion strength and high porosity. Fragmentation of splats can be caused by two entirely different mechanisms. If contact between the droplet and substrate is poor, the splat spreads into a thin sheet liquid and ruptures, producing a small central splat surrounded by a ring of debris. If contact is good and solidification is very rapid, a solid ring forms around the edges of the spreading droplet that obstructs the outward flowing liquid and destabilizes it, resulting in a splat with long peripheral fingers. If the solid layer grows by a significant amount during spreading, but not enough to destabilize the flow, it restrains the splat from spreading and becoming thin enough to rupture, and produces a disk shaped splat with no fragmentation. Numerical models of droplet impact can be used to simulate all three types of impact, with the rate of solidification varied by changing the value of thermal contact resistance between the splat and substrate. To predict which splat shape is likely for a given set of impact conditions, a dimensionless solidification parameter is defined, taking into account droplet diameter and velocity, substrate temperature, thermal contact resistance and thermo-physical properties of the splat and substrate. Examination of plasma-sprayed nickel, molybdenum, and zirconium droplets landing on glass, steel and Inconel substrates confirmed that the solidification parameter can be used to predict splat morphology.


Articles with similar content:

WETTABELITY AND CORROSION OF SOME NITRIDE OR ALUMINA CERAMICS BY A Si-Ca TREATED LIQUID STEEL
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.6, 2002, issue 4
J. C. Labbe, A. Amadeh, P. E. Quintard
IGNITION AND COMBUSTION OF BORON PARTICLES
International Journal of Energetic Materials and Chemical Propulsion, Vol.2, 1993, issue 1-6
S. C. Li, Forman A. Williams
HEAT TRANSFER AND NON-EQUILIBRIUM PHASE CHANGE OF LAMELLAE UNDER PLASMA SPRAY CONDITIONS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.11, 2007, issue 2
Dominique Gobin, Y. Lahmar-Mebdoua, Pierre Fauchais, Armelle Vardelle
LIQUID PROPERTY AND NOZZLE EFFECTS ON FLIGHT TIME OF PULSED JET SPRAY
Atomization and Sprays, Vol.14, 2004, issue 2
D. C. Slaughter, Daniel Downey, D. Ken Giles
TESTING OF METAL POWDERS BEHAVIOR IN A HOT STAGE MICROSCOPE
International Journal of Energetic Materials and Chemical Propulsion, Vol.5, 2002, issue 1-6
Alon Gany, Valery Rosenband