Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.737 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 30, 2020 Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2016013860
pages 169-188

EFFECT OF ATOMIZER INTERNAL GEOMETRY ON THE INTERNAL AND EXTERNAL TWO-PHASE FLOW IN EFFERVESCENT ATOMIZATION

Mona Hassanzadeh Jobehdar
Department of Mechanical and Materials Engineering, University of Western Ontario, London, Ontario, Canada
Kamran Siddiqui
Department of Mechanical and Materials Engineering, University of Western Ontario, London, Ontario, Canada
Aly H. Gadallah
Department of Mechanical and Materials Engineering, University of Western Ontario, London, Ontario, Canada; Department of Mechanical and Power Engineering, Tanta University, Tanta, Egypt
Wajid A. Chishty
Institute for Aerospace Research National Research Council Canada, Ottawa, Ontario, Canada

Краткое описание

An experimental study was conducted to study the internal and external two-phase flow in an effervescent atomizer using high-speed imaging. The impact of the aerator tube configuration and mixing zone length on the size of bubbles inside the mixing zone and the spray droplet characteristics at different gas-to-liquid flow rates ratios were studied. An aerator tube with the conical end base was manufactured and tested. It is observed that the separation bubble at the trailing edge is suppressed by this configuration, which resulted in more uniform and smaller bubbles compared to the standard aerator tube with a flat base. The length of the mixing zone was found to have an impact on the bubble size distribution inside the mixing zone; more uniform and smaller bubbles are generated in the shorter mixing zone. The mixing zone length, however, does not show a distinct impact on the droplet velocity and size. It is concluded that a conical base aerator tube and a shorter mixing zone could significantly improve the spray steadiness and the atomization process.


Articles with similar content:

EFFECT OF SINGLE- AND MULTI-HOLE BUBBLE BREAKERS ON THE EFFERVESCENT ATOMIZATION PROCESS
Atomization and Sprays, Vol.26, 2016, issue 2
Aly H. Gadallah, Kamran Siddiqui, Mona Hassanzadeh Jobehdar, Wajid A. Chishty
EXPERIMENTAL STUDY ON SPRAY AND MIXTURE PROPERTIES OF THE GROUP-HOLE NOZZLE FOR DIRECT-INJECTION DIESEL ENGINES, PART II: EFFECTS OF INCLUDED ANGLE AND INTERVAL BETWEEN ORIFICES
Atomization and Sprays, Vol.19, 2009, issue 4
Keiya Nishida, Jian Gao, Yuhei Matsumoto
NUMERICAL ANALYSIS OF THE INFLUENCE OF DIESEL NOZZLE DESIGN ON INTERNAL FLOW CHARACTERISTICS FOR 2-VALVE DIESEL ENGINE APPLICATION
Atomization and Sprays, Vol.23, 2013, issue 2
Joaquin De la Morena, Kshitij Neroorkar, Alejandro H. Plazas, David P. Schmidt, Richard C. Peterson
NUMERICAL INVESTIGATION ON EFFECTS OF ELLIPTICAL DIESEL NOZZLE ON PRIMARY SPRAY CHARACTERISTICS BY LARGE EDDY SIMULATION (LES)
Atomization and Sprays, Vol.28, 2018, issue 8
Bifeng Yin, Bin Xu, Shenghao Yu, Ze Ye, Huaping Xu, Hekun Jia, Weixin Deng
SPRAY CHARACTERISTICS OF DIESEL FUEL CONTAINING DISSOLVED CO2
Atomization and Sprays, Vol.21, 2011, issue 11
Eran Sher, M. Karaeen