Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.737 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 30, 2020 Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015012258
pages 483-511

REVIEW OF FUEL SPRAY DISTRIBUTIONS TO PREDICT PERFORMANCE OF ROTARY ATOMIZERS IN A SLINGER GAS TURBINE COMBUSTOR

Bernard Paquet
Combustion Laboratory, Mechanical Engineering Department, Laval University, Quebec, QC, Canada G1V0A6
Alain de Champlain
Combustion Laboratory, Mechanical Engineering Department, Laval University, Quebec, QC, Canada G1V0A6
Small Kalla
Combustion Laboratory, Mechanical Engineering Department, Laval University, Quebec, QC, Canada G1V0A6

Краткое описание

A research program was pursued on a rotary fuel nozzle commonly called a "slinger" atomizer for gas turbine application in order to characterize its spray distribution. The main advantage to be expected from this type of nozzle is a more uniform spray distribution leading to a more evenly distributed exit temperature at the combustor exit, thus providing a longer turbine life. In the course of this project, an in-depth open literature review was completed on rotary atomizers to find suitable correlations for an adequate spray distribution to eventually validate computational fluid dynamics (CFD) simulations to assess various potential injector configurations. After a substantial review of available correlations for the most promising types of rotary atomizers, i.e., flat disks, and plain (unperforated) and perforated cups, many uncertainties and inconsistencies were observed between reported test results and generated correlations to predict the average droplet size and a Rosin-Rammler spray distribution. A significant effort was devoted to validate and compare these found correlations in relation to their range of validity, to the flow regime, and to the measurement method for droplet diameters which showed as the most significant unknown parameters leading researchers to generate unreliable correlations. Ultimately after a thorough analysis, when comparing these three types of rotary atomizers for a given geometry and operating conditions, corresponding to a small typical gas turbine, the smallest SMD (based on idle condition) is achieved by the perforated cup operating in supercritical film mode, followed very closely by the plain cup, the flat disk, and the perforated cup operating in subcritical mode.


Articles with similar content:

SPRAY CHARACTERISTICS OF AN OPEN-END SWIRL INJECTOR
Atomization and Sprays, Vol.22, 2012, issue 5
Wei Zhang, Qing-Fei Fu, Kun-Da Cui, Li-Jun Yang
MOMENTUM ANALYSES FOR DETERMINATION OF DROP SIZE AND DISTRIBUTIONS DURING SPRAY ATOMIZATION
Atomization and Sprays, Vol.30, 2020, issue 2
Miroslav Raudensky, Hana Bellerova, T.-W. Lee, J. E. Park, Milan Hnizdl
FOCUSED-IMAGE HOLOGRAPHY AS A DENSE SPRAY DIAGNOSTIC
ICLASS 94
Proceedings of the Sixth International Conference on Liquid Atomization and Spray Systems, Vol.0, 1994, issue
Paul E. Sojka, Philip J. Santangelo
ANALYSIS AND TESTING OF FUEL REGRESSION RATE CONTROL IN SOLID FUEL RAMJETS
International Journal of Energetic Materials and Chemical Propulsion, Vol.5, 2002, issue 1-6
Alon Gany, Deborah Pelosi-Pinhas
CRITICAL EVALUATION OF MOMENTUM FLUX RATIO RELATIVE TO A LIQUID JET IN CROSSFLOW
Atomization and Sprays, Vol.28, 2018, issue 7
Scott Samuelsen, Scott B. Leask, Vincent G. McDonell