Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.262 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v20.i6.40
pages 525-552

EFFERVESCENT ATOMIZATION FOR INDUSTRIAL ENERGY−TECHNOLOGY REVIEW

Dancho Konstantinov
School of Engineering, Cardiff University, Wales, United Kingdom
Richard Marsh
School of Engineering, Cardiff University, Wales, United Kingdom
Phil J. Bowen
Cardiff School of Engineering, The Parade, Cardiff, CF24 3AA, United Kingdom
Andrew Crayford
School of Engineering, Cardiff University, Wales, United Kingdom

Краткое описание

Effervescent atomization technology is a process employing the creation of a two-phase flow between a liquid fuel and an aerating gas. This technology is receiving renewed interest in the industrial energy field due to its applicability to alternative fuels. This paper presents a review of the principal governing parameters controlling the atomization characteristics of effervescent systems. Previous research in this field has developed a number of systematic parameters relating to the operation of effervescent atomizers but none are universally applicable, i.e., a thorough first-principles-based understanding of effervescent atomization has not yet been achieved. This paper reviews initial operating conditions (gas-to-liquid ratio, pressure drop), fluid properties (liquid viscosity, liquid surface tension, fuel type, atomizing gas molecular weight, non-Newtonian fluids), and geometric constraints (atomizer geometry, exit orifice geometry). There is considerable agreement among researchers with regard to most of these parameters. By contrast, geometric constraints have not been satisfactorily optimized. Recommendations based on experimental work do exist for most geometric constraints. These could, however, almost certainly be further optimized. Also included in this work is a thorough review of the experimental correlations required to develop effervescent atomization systems, including resultant spray characteristics, injector internal flow, and bubble energy.


Articles with similar content:

ATOMIZATION OF ALLOY POWDERS
Atomization and Sprays, Vol.2, 1992, issue 3
Roger H. Rangel, Enrique J. Lavernia, Tirumalai S. Srivatsan
NUMERICAL INVESTIGATION OF TWO-PHASE FLOW IN AN EFFERVESCENT ATOMIZER FOR WATER MIST FIRE SUPPRESSION
Atomization and Sprays, Vol.21, 2011, issue 10
Lingyong Pan, Gang Yang, Baoren Li
The Specific Heat at Constant Pressure in the Latent Functional Fluid with Microencapsulated Phase-Change Materials
Journal of Enhanced Heat Transfer, Vol.9, 2002, issue 1
Wen-Qiang Lu, Fengwu Bai
NUMERICAL STUDY OF ELECTRIC REYNOLDS NUMBER ON ELECTROHYDRODYNAMIC (EHD) ASSISTED ATOMIZATION
Atomization and Sprays, Vol.27, 2017, issue 7
Patrick Sheehy, Mark Owkes
AN APPRAISAL OF SWIRL ATOMIZER INVISCID FLOW ANALYSIS, PART 2: INVISCID SPRAY CONE ANGLE ANALYSIS AND COMPARISON OF INVISCID METHODS WITH EXPERIMENTAL RESULTS FOR DISCHARGE COEFFICIENT, AIR CORE RADIUS, AND SPRAY CONE ANGLE
Atomization and Sprays, Vol.19, 2009, issue 3
John Joss Chinn