Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.262 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2015013216
pages 755-773

TIME-RESOLVED CHARACTERIZATION OF LOW-PRESSURE PULSED INJECTOR

Rohit Singh Pathania
Department of Mechanical Engineering, National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India
Satyanarayanan R. Chakravarthy
Department of Aerospace Engineering, National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India
Pramod S. Mehta
Department of Mechanical Engineering, National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India

Краткое описание

This study concerns visualization of pulsed sprays of a gasoline port fuel injector under ambient conditions. One-, two-, and four-hole configurations all with the same hole diameter are compared. The investigations on the two-hole configuration include adjacent and diagonal holes. The instantaneous penetration length, the jet breakup length, cone angle, and the droplet diameter distributions are evaluated along the spray axis at different injection pressures. As the spray penetration evolves, the liquid jet breaks up some time later, and reaches a nearly constant breakup length throughout the subsequent development of the spray. Unlike the single-hole spray, the two-hole spray exhibits a mild increase in the breakup length with increase in the injection pressure. The breakup length with the diagonal two-hole configuration is much shorter than with the adjacent one. The diagonal two-hole configuration exhibits a high cone angle relative to two-hole and four-hole cases. In all the cases, the mean droplet size decreases with injection pressure and remains nearly constant in time at any axial location. While the single-hole and adjacent two-hole injectors indicate coalescence of droplets, the diagonal two-hole case shows a decrease in the Sauter mean diameter of the droplets with axial distance. The four-hole injector produces nearly constant droplet size. The shorter breakup length, higher spread, and smaller droplet sizes in the two-hole diagonal configuration support an enhanced entrainment of ambient air as compared to the two-hole adjacent and four-hole injector configurations.


Articles with similar content:

EXPERIMENTAL STUDY OF SPRAY BREAKUP PHENOMENA IN SMALL-SCALE SIMPLEX ATOMIZERS WITH AND WITHOUT AIR SWIRL
Atomization and Sprays, Vol.28, 2018, issue 4
Muralidhara Suryanarayana Rao, Srinivasan Kothandaraman, Muthuselvan Govindaraj, Kushal D. Ghate, Venkat S. Iyengar, Sundararajan Thirumalachari
EXPERIMENTAL INVESTIGATIONS ON A PIEZO-ACTIVATED HOLLOW CONE INJECTOR − PART II: THE INFLUENCE OF NEEDLE LIFT ON DROPLET SIZE DISTRIBUTIONS AND VORTEX FORMATION
Atomization and Sprays, Vol.24, 2014, issue 10
Graham Wigley, Konstantinos Boulouchos, B. Schneider, Andreas Schmid
CHARACTERISTICS OF TRANSIENT, SWIRL-GENERATED, HOLLOW-CONE SPRAYS
Atomization and Sprays, Vol.16, 2006, issue 5
Julian T. Kashdan, John S. Shrimpton
PLANAR LIQUID SHEET BREAKUP OF PREFILMING AND NONPREFILMING ATOMIZERS AT ELEVATED PRESSURES
Atomization and Sprays, Vol.19, 2009, issue 12
Umesh Bhayaraju, Christoph Hassa
SPRAY CHARACTERISTICS OF A PRESSURE-SWIRL FUEL INJECTOR SUBJECTED TO A CROSSFLOW AND A COFLOW
Atomization and Sprays, Vol.21, 2011, issue 8
Barry Kiel, Ryan G. Batchelor, Amy Lynch, Mark Reeder, James Gord, Joseph Miller