Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.262 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v21.i1.20
pages 17-29

Geometric Primary Atomization Characteristics in an Airblast Atomizer, High Pressure Conditions

Vital Gutierrez Fernandez
Heterogeneous, Multiphase Flows Unit, Aerodynamic and Energetic Models Department, Office National d'Etudes et de la Recherche Aérospatiales (ONERA), Toulouse, France
G. Lavergne
Heterogeneous, Multiphase Flows Unit, Aerodynamic and Energetic Models Department, Office National d'Etudes et de la Recherche Aérospatiales (ONERA), 31055 Toulouse Cedex 4, France
P. Berthoumieu
Heterogeneous, Multiphase Flows Unit, Aerodynamic and Energetic Models Department, Office National d'Etudes et de la Recherche Aérospatiales (ONERA), 31055 Toulouse Cedex 4, France

Краткое описание

An experimental study via fast camera visualizations was accomplished to analyze the primary atomization. The injection device consisted in a planar airblast atomizer, which generated a 300μm thickness liquid sheet. The system considered, kept its geometry constant, while the fluids flow was modified to produce a wide range of conditions. This was achieved by adjusting the fluids' momentum flux. In the case of the gas, both the air velocity across the airblast atomizer and its absolute pressure were varied. The latter parameter reached a value of 11 bar. Additionally, two liquids, water and Kerosene Jet A1 were injected at several velocities. The manuscript includes results for the break-up length, transversal wavelength, and longitudinal ligaments length. The behaviour of these characteristics was strongly affected by the atomization mechanism at which they were measured. Consequently, a set of image proceses techniques were developed to measure these characteristics. Finally, a set of empirical relsations are proposed to predict the magnitude of these characteristics at the tested conditions.


Articles with similar content:

Dynamic Primary Atomization Characteristics in an Airblast Atomizer, High Pressure Conditions
Atomization and Sprays, Vol.21, 2011, issue 1
Vital Gutierrez Fernandez, P. Berthoumieu, G. Lavergne
SPRAY BEHAVIOR OF THE ROTARY ATOMIZER WITH IN-LINE INJECTION ORIFICES
Atomization and Sprays, Vol.20, 2010, issue 10
Seong Ho Jang, Seong Man Choi
INJECTION OF WATER-IN-OIL EMULSION JETS INTO A SUBSONIC CROSSFLOW: AN EXPERIMENTAL STUDY
Atomization and Sprays, Vol.24, 2014, issue 4
Guillermo A. Gomez, Christopher D. Bolszo, G. Scott Samuelsen, Vincent McDonell
DEVELOPMENT OF AN AIR-BLAST ATOMIZER FOR INDEPENDENT CONTROL OF DROPLET SIZE AND SPRAY DENSITY
Atomization and Sprays, Vol.14, 2004, issue 3
C. P. Koshland, R. F. Sawyer, H. L. Clack, D. Lucas
EFFECT OF SWIRL CHAMBER LENGTH ON THE ATOMIZATION CHARACTERISTICS OF A PRESSURE-SWIRL NOZZLE
Atomization and Sprays, Vol.27, 2017, issue 10
Jeekeun Lee, Reza Alidoost Dafsari, Foad Vashahi