Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.262 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 1.6

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v18.i1.10
pages 1-47

MODELING OF STEADY-STATE HEAT TRANSFER IN A WATER SPRAY IMPINGEMENT ONTO A HEATED WALL

J. C. Landero
School of Mechanical, Aerospace and Civil Engineering, University of Manchester, Manchester M60 1QD, UK
A. Paul Watkins
Energy and Multiphysics Research Group, School of Mechanical, Aerospace, and Civil Engineer- ing, University of Manchester, United Kingdom

Краткое описание

The application of the work presented in this paper is that of the cooling by water spray impingement of hot surfaces as used, for example, in steel manufacture. A new spray impingement heat transfer model has been developed on the basis of the engineering superposition principle. The heat transfer and drop hydrodynamic phenomena occurring during spray cooling are intimately related but uncoupled in the model. To make these phenomena independent, impaction-behavior data were extracted from experimental data based on steady-state conditions in the literature [S. Chandra and C. T. Avedisian, Proc. R. Soc. London, Ser. A, vol. 432, pp. 13−41, 1991; J. D. Bernardin, C. J. Stebbins, and I. Mudawar, Int. J. Heat Mass Transfer, vol. 40, no. 2, pp. 247−267, 1997], and transient heat transfer data were obtained by means of an in-house computational code. The model is used here to predict the heat flux from a constant-temperature hot surface to the spray for the three heat transfer boiling regimes under the following droplet impingement Weber number and wall temperature ranges: 0 < We < 1000 and 373 K < TW < 573 K, under normal pressure conditions. The model performance is tested against one major set of steady-state experimental heat transfer data taken from the literature [R. A. Sharief, G. G. Nasr, A. J. Yule, J. R. Jeong, and D. D. James, Proc. of ICLASS-2000, Pasadena, CA (on CD-ROM), 2000] to assess the accuracy of the computer model. The data were obtained from four full-cone water atomizers, which were used to experimentally extract heat from a heated test piece. The spray experiment used different impaction distances, injection pressures, and wall temperatures. The heat transfer model predictions are compared to 18 different experimental conditions and reasonable agreement is obtained in many cases. The discrepancies in the other cases are partly attributed to assumptions made in the spray model. Deficiencies in the heat transfer model are identified in the conclusions.