High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
Publicado 4 números por año
ISSN Imprimir: 1093-3611
ISSN En Línea: 1940-4360
IF:
0.4
Immediacy Index:
0.1
Eigenfactor:
0.00005
JCI:
0.07
SJR:
0.198
SNIP:
0.48
CiteScore™::
1.1
H-Index:
20
Indexed in
Volumen 13, 2009 Edición 1
DOI: 10.1615/HighTempMatProc.v13.i1
CHARACTERIZATION OF THE WIRE ARC SPRAY PROCESS VIA IMAGE ANALYSIS, IN-FLIGHT PARTICLE CHARACTERISTICS AND COATING PROPERTIES
pp. 1-23
DOI: 10.1615/HighTempMatProc.v13.i1.10
EXPERIMENTAL DETERMINATION OF THERMAL PLASMA TEMPERATURES
pp. 25-44
DOI: 10.1615/HighTempMatProc.v13.i1.20
INFLUENCE OF THE SELF-ABSORPTION OF ATOMIC LINES ON THE DETERMINATION OF TEMPERATURE AND ELECTRON NUMBER DENSITY IN THE CASE OF A LASER INDUCED CaCl2 − WATER PLASMA
pp. 45-59
DOI: 10.1615/HighTempMatProc.v13.i1.30
ELECTRICAL CHARACTERISATION OF VERY HIGH PRESSURE Ar/H2 LOW CURRENT ARC DISCHARGE
pp. 71-76
DOI: 10.1615/HighTempMatProc.v13.i1.50
SPLAT HEAT TRANSFER AND CRYSTAL GROWTH UNDER THERMAL SPRAY CONDITIONS
pp. 77-91
DOI: 10.1615/HighTempMatProc.v13.i1.60
INVESTIGATION OF A SURFACE DIELECTRIC BARRIER DISCHARGE DEDICATED TO BOUNDARY LAYER CONTROL
pp. 93-105
DOI: 10.1615/HighTempMatProc.v13.i1.70
AROMATIC VOC REMOVAL BY MICROPARTICLES FORMATION IN PURE NITROGEN
pp. 107-119
DOI: 10.1615/HighTempMatProc.v13.i1.80
Último edicion
DETERMINATION OF THE MASS BALANCE OF HIGH-CARBON FERROCHROME IN A SUBMERGED ARC FURNACE
RHEOLOGICAL BEHAVIOR AND 3D PRINTING OF HIGHLY FILLED ALUMINA-POLYAMIDE FILAMENTS DURING FUSED DEPOSITION MODELING
SCRATCH TESTING OF ZrN COATING ON TI-6AL-4V TITANIUM ALLOY SURFACE PRELIMINARY TREATED BY COMPRESSION PLASMA FLOWS IMPACT
ELECTRON-BEAM SINTERING OF ZIRCONIUM DIOXIDE/TITANIUM CERAMICS FOR MICROELECTRONICS PRODUCTS
THE EFFECT OF THE FLUORINE CONCENTRATION IN A PLASMA-FORMING GAS MIXTURE ON THE CHEMICAL COMPOSITION, SURFACE CHARGE, AND RELIEF PARAMETERS OF FLUOROCARBON COATINGS ON PET
PREPARATION AND THERMOELECTRIC PROPERTIES OF p-TYPE Ag(1-x)Cu(1+x)Te SAMPLES BY SPARK PLASMA SINTERING METHOD
ELECTRON-BEAM SYNTHESIS OF ZIRCONIA CERAMIC COATINGS IN THE FOREVACUUM PRESSURE RANGE
INCREASING THE WEAR RESISTANCE OF TITANIUM ALLOYS BY DEPOSITION OF A MODIFYING COATING (Zr,Nb)N
PHYSICAL AND MECHANICAL PROPERTIES AND OPERATIONAL CHARACTERISTICS OF CORONA SPRAYED POWDER COATINGS
Próximos Artículos
Application of a non-self-sustained glow discharge initiated by a focused electron beam in the forevacuum pressure region for nitriding the inner surface of narrow metal tubes
PLASMA DISCHARGE IN LIQUID MEDIA UNDER THE EFFECT OF ULTRASOUND FOR THE SYNTHESIS OF FILLERS FOR POLYMER COMPOSITES WITH ENHANCED MECHANICAL STRENGTH AND GAS PERMEABILITY
THE QUALITY OF THIN-WALLED STRUCTURES OF AlSi10Mg PRODUCED BY SELECTIVE LASER MELTING
Electron-beam synthesis of zirconia ceramic coatings in the forevacuum pressure range
Preparation and Thermoelectric Properties of P-type Ag(1-x)Cu(1+x)Te Samples by SPS Method
The effect of the fluorine concentration in a plasma-forming gas mixture on the chemical composition, surface charge and relief parameters of fluorocarbon coatings on PET
Electron beam sintering of zirconium dioxide/titanium ceramics for microelectronics products